135
Harris M7100 Wireless Interface Option
?,Config : C
“Ch Type = Orion” indicates support for Orion, J725M, and M7100 radios.
4. Press "C" to configure a channel.
chA,chB,Flash,<BS> : A
5. You can then select which channel to configure by pressing “A” or “B”. In this
example we are configuring channel A.
6. Once you select a channel you have the option of reviewing or defining setting for
the channel.
Define,Review,Store,Init,<BS> : D
7. Press “D” to define a channel. The options you can define are :
• Log - Enable/Disable diagnostic logging. Displays event and state information
that can be used to diagnose problems.
• Volume - Set relative radio volume (20% to 100%).
• voX enable - Determines if received audio controls incoming calls. Required
to support PL calls on Orion radios. When enabled, incoming call state is
determined by either VOX or the status of the “Busy” LED on the radio. When
disabled, incoming call state is determined solely by the status of the “Busy”
LED on the radio.
• vox Threshold - Received audio level that triggers call detection. Levels above
the threshold will trigger a call indication. Selectable from -32 to -18 dbm.
• vox Delay - Determines how long the audio must be below the vox Threshold
before the call is cleared. Selectable from .5 to 4.0 seconds.
8. The logging options:
Log,Volume,voX enable,vox Threshold,vox Delay,<BS> : L
Disable,Enable,<BS> : #
Zetron recommends log disabled (
D
).
9. The volume options:
Log,Volume,voX enable,vox Threshold,vox Delay,<BS> : V
A:20%, B:40%, C:60%, D:80%, E:100%, <BS> : #
Zetron recommends 100% (
E
).
10. The Vox options (default is enabled):
Log,Volume,voX enable,vox Threshold,vox Delay,<BS> : X
Disable,Enable,<BS> : #
Zetron recommends VOX enabled (
E
) unless you have an older firmware version
(see note above).
Tip
The recommended setting for VOX depends upon your firmware
version. These recommendations are only valid for Orion/M7100
firmware (P/N 601-0903).
• V1.00 to V1.16: VOX can be enabled with radios configured
for conventional operation if desired, but will cause problems
on trunked systems.
• V1.17 to V1.22: VOX can be enabled if desired.
• V1.24.01: VOX is recommended to be enabled.
Содержание 4000 Series
