297
SECTION 33 - SYSTEM CALIBRATION, SERVICE SETPOINTS, AND RESET PROCEDURES
FORM 160.54-M1
ISSUE DATE: 10/25/2019
JOHNSON CONTROLS
JCI COMPANY CONFIDENTIAL
33
6. If Disable is selected in step 4, press the SHUT-
DOWN key.
7.
Use the ◄ and ► keys to select Enable or Disable
as desired per above.
8. Press ENTER (
) key.
MOTOR LUBRICATION NOTIFICATION
This feature applies to OptiView Panel 03630 Software
version Y.OPT.01.00D.308 (and later).
The MOTOR LUBRICATION Screen, accessible from
the MOTOR Screen in any access level, displays infor-
mation applicable to this feature.
This feature provides an indication when the compres-
sor motor lubrication is required. The lubrication re-
quirement and notification is based on the OPERATING
HOURS SINCE LAST MOTOR LUBRICATION.
There are up to three levels of notification, each in-
dicating an increasing level of urgency. WARNING
– MOTOR BEARING LUBE SUGGESTED is dis-
played when the hours exceed the service level setting
for lubrication (750 to 15000; Default 1200 hours) mi-
nus 200 hours. If there is no response, WARNING –
MOTOR BEARING LUBE REQUIRED is displayed
when the hours exceed the lubrication interval setting.
If there is still no response, a safety shutdown is per-
formed when the hours exceed lubrication interval set-
ting plus 200 hours. MOTOR – LACK OF BEARING
LUBRICATION is then displayed.
To provide a record of when a motor lubrication is
performed, the operator enters his/her initials, name or
User ID using the MOTOR LUBE ACKNOWLEDGE
key on the MOTOR LUBRICATION Screen. The date
and time of this entry is automatically logged as the
Date of Last Lubrication and Time of Last Lubrica-
tion. This also clears any motor lubrication warning or
safety that is in effect and resets the Operating Hours
Since Last Lubrication to zero.
The MOTOR LUBRICATION Screen, accessible from
the MOTOR Screen in any access level, displays infor-
mation applicable to this feature.
When both motor bearings have been lubricated, the
operator must acknowledge the lubrication has been
performed. This is done by entering his/her initials,
name or User ID as a 3 to 8 character string. The entry
is displayed as the operator initials at Last Lubrication.
The date and time of this entry is automatically logged
as the Date of Last Motor Lubrication and Time of Last
Motor Lubrication. This entry also resets the Operating
Hours Since Last Lubrication to zero.
This entry also resets the motor lubrication warning
messages: WARNING – MOTOR BEARING LUBE
SUGGESTED, WARNING – MOTOR BEARING
LUBE REQUIRED and safety shutdown MOTOR –
LACK OF BEARING LUBRICATION.
Enter your initials, name or User ID using the follow-
ing procedure. The entry must be a minimum of 3 char-
acters and a maximum of 8 characters.
1. At the keypad, log on at using Password 9 6 7
5. If resetting the safety shutdown “Motor – Lack
of Lubrication”, place COMPRESSOR switch in
Stop position.
2. Press the MOTOR LUBE ACKNOWLEDGE
key. A dialog box appears. A red box highlights
the first changeable location.
3.
Use the ▲▼ keys to scroll sequentially through
the alphabet to enter letters or numbers. Each time
the ▲ is pressed, the next higher sequential al
-
phabet letter or number is displayed. Each time
the ▼ is pressed, the next lower alphabet letter
or number is displayed. When the desired letter
or number is displayed, use the ► key to forward
space the red box for the next entry. Use the ◄
key to backspace, if necessary.
4. To write over an existing entry or to place a blank
space, scroll to the beginning of the alphabet. The
selection before the letter A is a blank space. Use
the • key to enter a period/decimal point. During
the entry process, if it is desired to exit the dialog
box and retain the previous entry, press the CAN-
CEL (X) key.
5. When all of the desired characters have been en-
tered, press the ENTER (
) key.
Motor Lube Date
Normally, the Date of Last Lubrication is automatically
recorded when the operator enters his/her initials, name
or User ID with the MOTOR LUBE ACKNOWLEDGE
key in the above procedure. However, if it is necessary
to modify the motor lubrication date after that procedure
was performed, proceed as follows:
1. At the keypad, login at ADMIN access level.
2. Press the Motor Lube Date key.
3. Using the number keys, enter the desired date.
4. Press the ENTER (
) key.
