YOKOGAWA ScopeCorder DL950 Скачать руководство пользователя страница 176 | Manualshive

Страница: 176 / 316

background image

11-8

IM DL950-02EN

11.3 Performing Cyclic Statistical Processing

This section explains the following settings for performing cycle statistic processing on the
displayed waveforms):

Items Common to Scope Mode and Recorder Mode

•  Turning cycle statistics on
•  Source waveform used to determine the cycle
•  Displaying results

► “Cyclic Statistical Processing (Cycle)” in the Features Guide

MEASURE Statistics Menu

1.

On the waveform screen’s MENU, tap

ANALYSIS

>

MEASURE

, or press

MEASURE

.

2.

Tap

Statistics

, or press the soft key. The following screen appears.

Set the measurement

time period.

► sec. 11.1

Turns automated

measurement on or off

► sec. 11.1

Set the source waveform

and measurement items.

► sec. 11.1

Detail setup

► sec. 11.1

Set the indicator.

► sec. 11.1

Configure Area2.

► sec. 11.1

Set Mode to ON.

Set Type to Cycle.

See “Setting the Cycle Trace.”

Executes measurement

See “Displaying the

Measured Results.”

Measure menu

Statistics menu

Configure statistical

processing.

Setting the Cycle Trace (Trace)

3.

Tap

Trace

, or press the soft key. Select the cycle trace from the following.

Depending on the channel you select, you need to select sub channels and bits.

•Own:
The instrument determines the period of each source waveform. It then automatically
measures the waveform parameters and performs statistical processing once per period.
However, if signals that have different periods are applied to multiple channels, the number
of iterations of automated measurement and statistical processing for each signal is equal
to the number of periods in the slowest signal.
• CH1 to CH16, 16CH TEMP/VOLT, CAN, CAN FD, LIN, SENT, Math1 to Math8, FFT1 to
FFT8:
The instrument automatically measures the waveform parameters of all the source
waveforms and performs statistical processing on the measured values for each cycle of
the specified channel.

«
...
174
175
176
177
178
...
»

Содержание ScopeCorder DL950





























































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ScopeCorder DL950

Бренд: Danfoss Страницы: 8

Бренд: RayTek Страницы: 72

Бренд: Magnetrol Страницы: 40

Бренд: Cannon Страницы: 64

Бренд: Cannon Страницы: 73

Бренд: Kathrein Страницы: 10

Wind Monitor Series

Бренд: Campbell Страницы: 38

Бренд: Favero Electronics Страницы: 12

Veeder-Root 7990 Series

Бренд: Danaher Страницы: 8

CoolPoint CP12-V8

Бренд: UFM Страницы: 14

Nitro-Save NS16

Бренд: TDI Страницы: 4

Panametrics Aurora H2O

Бренд: Baker Hughes Страницы: 92

Бренд: phase II Страницы: 11

MultiScanner HD800 OneStep

Бренд: Zircon Страницы: 2

Бренд: HERON Страницы: 2

Бренд: E+E Elektronik Страницы: 48

Roast Alert/3 ET-8C

Бренд: Redi-Chek Страницы: 3

AquaShock 850046K

Бренд: Sper scientific Страницы: 28

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды