YOKOGAWA ScopeCorder DL950 Скачать руководство пользователя страница 133

Страница: 133 / 316

6-5

IM DL950-02EN

Measuring X-Y Waveforms with Horizontal Cursors (Horizontal)

Tap

Type

, or press the soft key to select

Horizontal

See “Setting Measurement Items.”

Set the cursor positions (Cursor1: Y1, Cursor2: Y2).

You can also drag the cursors on the X-Y screen. Tap the cursor and

then tap the arrow that appears (shown in the figure below) to adjust

the cursor position in fine increments.

Select the trace to measure with cursors (XY1 to XY8).

Set the cursor type to Horizontal (horizontal).

Set Mode to ON.

Setting Measurement Items (Item Setup)

Tap

Item Setup

, or press the soft key. The following screen appears.

Select the measurement items that you want to use.

Y1: Vertical (Y axis) value at Cursor1

Y2: Vertical (Y axis) value at Cursor2

ΔY: Difference between the vertical (Y axis) values of

Cursor1 and Cursor2

6.3 Measuring X-Y Waveforms with Cursors

Содержание ScopeCorder DL950





























































































































































































































































































































Результаты поиска

Содержание ScopeCorder DL950

Отзывы:

Бренды по названию

Популярные бренды

YOKOGAWA ScopeCorder DL950, Руководство пользователя

Результаты поиска

Содержание ScopeCorder DL950

Отзывы:

Бренды по названию

Популярные бренды