YOKOGAWA ScopeCorder DL950 Скачать руководство пользователя страница 90

Страница: 90 / 316

4-2

IM DL950-02EN

4.1 Setting the Trigger Mode

This section explains the following trigger settings:

Applicable in Scope Mode

• Trigger mode

► “Trigger Mode (Trigger Mode)” in the Features Guide

Trigger Mode Menu

On the waveform screen’s

MENU

, tap

TRIGGER

MENU

, or press

TRIG.MENU

. A trigger

menu appears.

Tap

Trigger Mode

, or press the soft key. The trigger mode options are displayed.

Set the trigger mode.

Trigger menu

Set the trigger position, trigger

delay, and hold-off ► sec. 4.2

Select Simple or Enhanced.

Set the trigger source.

► sec. 4.3

Set the trigger slope.

► sec. 4.3

Set the trigger level.

► sec. 4.3

Set the trigger hysteresis.

► sec. 4.3

Setting the Trigger Mode (Trigger Mode)

Tap the trigger mode you want to use, or press the soft key.

Auto:

If the trigger conditions are met within a 50-ms timeout period, the instrument

updates the displayed waveforms on each trigger occurrence. If not, this

instrument automatically updates the displayed waveforms. If the time axis is set

to a value that would cause the display to switch to roll mode, roll mode display

will be enabled.

Auto Level: If a trigger occurs before a timeout (which is approximately 1 second), the

instrument updates the waveform in the same way that it does in Auto mode. If a

trigger does not occur before a timeout, the instrument automatically changes the

trigger level to the center value of the trigger source amplitude, triggers on that

value, and updates the displayed waveform.

Normal:

The instrument updates the waveform display only when the trigger conditions

are met.

Single:

When the trigger conditions are met, the instrument updates the displayed

waveform once and stops signal acquisition. If the time axis is set to a range that

causes the display to switch to roll mode, the roll mode display will be enabled.

When the instrument triggers, it begins recording data. When data has been

acquired up to the amount specified by the set record length, the waveform

display stops.

Содержание ScopeCorder DL950





























































































































































































































































































































Результаты поиска

Содержание ScopeCorder DL950

Отзывы:

Бренды по названию

Популярные бренды

YOKOGAWA ScopeCorder DL950, Руководство пользователя

Результаты поиска

Содержание ScopeCorder DL950

Отзывы:

Бренды по названию

Популярные бренды