YOKOGAWA ScopeCorder DL950 Скачать руководство пользователя страница 288

Страница: 288 / 316

21-2

IM DL950-02EN

21.1 Setting Time Synchronization Mode

This section explains the following setting for synchronizing instruments on a network.

Items Common to Scope Mode and Recorder Mode

•  Time synchronization mode
•  Configuring IRIG settings
•  Configuring IEEE1588 settings

► “Time Synchronization” in the Features Guide

Utility System Config Time Sync Menu

On the waveform screen’s MENU, tap

OTHERS

UTILITY

, or press

UTILITY

Tap

System Config

, or press the soft key.

Tap

Time Sync

, or press the soft key. The following screen appears.

Select System

Config.

Select

Time Sync.

See “Setting the

Synchronization Mode.”

See “Configuring

IEEE1588 Settings.”

See “Configuring

IRIG Settings.”

Setting the Synchronization Mode (Time Sync)

Tap

Time Sync

, or press the soft key. The following screen appears.

GPS (when the IRIG, GPS (/C35) option is installed)
IRIG (when the IRIG, GPS (/C35) option is installed)

IEEE1588

Содержание ScopeCorder DL950





























































































































































































































































































































Результаты поиска

Содержание ScopeCorder DL950

Отзывы:

Бренды по названию

Популярные бренды

YOKOGAWA ScopeCorder DL950, Руководство пользователя

Результаты поиска

Содержание ScopeCorder DL950

Отзывы:

Бренды по названию

Популярные бренды