YOKOGAWA ScopeCorder DL950 Скачать руководство пользователя страница 294

Страница: 294 / 316

22-3

IM DL950-02EN

Install it with the latch lever tilted down. If it is installed with the latch lever raised, it cannot be
installed normally.

Tilt the latch lever.

Back

Input module

SFP module

(720941)

Link connector

Note

• Be sure to use the 720941 optional accessory for the SFP module. If you use a different SFP module,

the instrument’s functions and performance are not guaranteed. In addition, a malfunction caused by

using a different SFP module is not covered by warranty.

• There are connectors with the same shape as those of link connectors on the left side of the instrument’s

front panel, but they are 10G Ethernet connectors. You cannot use them to connect SFP modules.

Removing SFP Modules

Turn off the instrument.

Remove the optical fiber cord from the instrument.

Raise the latch lever on the SFP module toward you and slowly pull the module out. The

connector will be disengaged, and the SFP module will come out of the link connector.

Raise the latch lever.

22.1 Connecting Multiple Instruments

Содержание ScopeCorder DL950





























































































































































































































































































































Результаты поиска

Содержание ScopeCorder DL950

Отзывы:

Бренды по названию

Популярные бренды

YOKOGAWA ScopeCorder DL950, Руководство пользователя

Результаты поиска

Содержание ScopeCorder DL950

Отзывы:

Бренды по названию

Популярные бренды