Yealink MeetingSpace VC200 страница 143 Скачать руководство пользователя

Страница: 143 / 232

| Configuring Content Sharing |

143

•

LAN Connection

: Make sure the Yealink video conferencing system and the control system are in the same

network segment. If you use this mode to control the system, TCP protocol is recommended. To establish a

connection, the control system needs to know the IP address and TCP port of the Yealink video conferencing

system.

•

Serial Connection

: The USB port on the Yealink video conferencing system can be connected to the serial port on

the control system through a USB to RS-232 cable.

For more information, refer to

Yealink VC Deployment and User Manual for Control Systems

and

API Commands

Introduction for Yealink Video Conferencing System

Configuring Content Sharing

You can select dual-stream protocol or mix sending method to share content, and you can configure the mode, the

frame rate and the resolution for the shared content.

Note:

If the far site does not support the dual-stream protocol, you can select the Mix Sending feature to mix the

video and content, and then send them to the far site in one stream.

•

Configuring Dual-Stream Protocol

•

Configuring Mix-Sending

•

Configuring Content Sharing

Configuring Dual-Stream Protocol

The dual-stream protocol allows the video and PC content to be transmitted to the far site simultaneously, thus

meeting the requirements of different conference scenarios, such as training or medical consultation. Based on this

protocol, the participants can share contents while having a video call.
The Yealink video conferencing system supports the standard H.239 protocol and BFCP (Binary Floor Control

Protocol).
•

Configuring the H.239 protocol

•

Configuring BFCP (Binary Floor Control Protocol)

Configuring the H.239 protocol

H.239 protocol is used when sharing content with the far site in H.323 calls.

Procedure

Do one of the following:
• On your web user interface, go to

Account

VC Platform

Video Conference Platform

Platform

Type

StarLeaf

• On your web user interface, go to

Account

H.323

Configure and save the following settings:

Parameter

Description

Configuration Method

H.239

Enable or disable the H.239

protocol.

Default

: On.

Web user interface

Содержание MeetingSpace VC200









































































































































































































































Результаты поиска

Содержание MeetingSpace VC200

Отзывы:

Похожие инструкции для MeetingSpace VC200

Бренды по названию

Популярные бренды

Yealink MeetingSpace VC200, Руководство администратора

Результаты поиска

Содержание MeetingSpace VC200

Отзывы:

Похожие инструкции для MeetingSpace VC200

Бренды по названию

Популярные бренды