YATO YT-83113 Скачать руководство пользователя страница 6

6

OPERATING INSTRUCTIONS

GB

RECHARGE RETEST - the battery is 

fl

 at and cannot be tested 

until it is fully charged. Disconnect the tester, charge the battery 

and repeat the test.

BAD REPLACE - the battery does not bear the load and should 

be replaced with a new one.

TEST ERROR - the tested battery has a CCA higher than 1200 

or the tester has not been properly connected to the battery. Dis-

connect the tester, recharge the battery, and after removing both 

of the above causes, repeat the test. In case of the same result, 

replace the battery immediately.  

STARTING SYSTEM TEST PROCEDURE

The test procedure can only be carried out with the battery in-

stalled in the car.

Connect the red tester clamp marked with “+” with positive bat-

tery terminal. Connect the black tester clamp marked with “-” with 

negative battery terminal or element of the car body to which the 

negative battery terminal is connected.

The tester display will be backlighted and after a while the BAT-

TERY TEST message appear, use the arrows to select SYSTEM 

TEST and after a while voltage value in volts, e.g. 12.28 V mes-

sage will appear. Press the ENTER button to proceed to the next 

step of the procedure.

The message TURN OFF LOADS START ENGINE will appear. 

Switch o

  all loads, e.g. lights, air conditioning, radio and start 

the engine; wait until the tester displays the cranking voltage. 

When the motor is running, one of the results and the current 

voltage indication will be displayed after the end of the test. 

CRANKING VOLTS NORMAL - the cranking voltage value is 

within the correct range.

CRANKING VOLTS LOW - the cranking voltage value is too low. 

Carry out the test procedure recommended by the car manufac-

turer to determine the cause. 

CRANKING VOLTS NOT DETECTED - the tester was not able 

to measure the cranking voltage value. Press the ENTER button 

and start the test procedure from the beginning. 

Press the ENTER button, PRESS ENTER FOR CHARGING 

TEST message will appear (press ENTER button to perform 

a charge test), press ENTER button again. The MAKE SURE 

ALL LOADS ARE OFF message will appear (make sure that all 

loads are switched o

 ). Switch o

  all loads and press the ENTER 

button.

At the end of the test, one of the results and the current voltage 

indication will appear.

ALT. IDLE VOLTS NORMAL - the alternator supplies su

  cient 

idle voltage.

ALT. IDLE VOLTS LOW - the alternator provides insu

  cient idle 

voltage.

ALT. IDLE VOLTS HIGH - the alternator supplies too high idle 

voltage.

Press the ENTER button, TURN ON LOADS AND PRESS EN-

TER message will appear (switch on the loads and press the 

ENTER). Switch on loads such as light, air conditioning, radio, 

etc. and press the ENTER button. At the end of the test, one of 

the results and the current voltage indication will appear.

ALT. LOAD VOLTS NORMAL - the alternator supplies su

  cient 

load voltage.

ALT. LOAD VOLTS LOW - the alternator supplied insu

  cient 

load voltage.

ALT. LOAD VOLTS HIGH - the alternator supplies too high load 

voltage.

DISPLAY BRIGHTNESS

After connecting the tester to the battery, press the ENTER but-

ton until the LCD BRIGHTNESS message (display brightness) 

and the current percentage of display brightness appear. Press 

the ENTER button again, then use the arrows to change the dis-

play brightness. Press the ENTER button to save the settings.  

DEVICE MAINTENANCE AND STORAGE

Clean the tester housing with a slightly damp cloth (water) and 

wipe it dry. Never immerse the tester in water or other liquids. 

Keep the tester clamps clean. If there are signs of corrosion or 

patina, clean the metal parts with a cleaning agent for the copper 

electrical terminals.

Store the tester separately so that it is not exposed to impacts, 

e.g. from other tools in the toolbox. The place of storage should 

be shaded and well ventilated. It should also protect against un-

authorised access, especially by children.

This symbol indicates that waste electrical and electronic equipment 

(including batteries and storage cells) cannot be disposed of with 

other types of waste. Waste equipment should be collected and 

handed over separately to a collection point for recycling and 

recovery, in order to reduce the amount of waste and the use of natural 

resources. Uncontrolled release of hazardous components contained 

in electrical and electronic equipment may pose a risk to human health 

and have adverse e

 ects for the environment. The household plays an 

important role in contributing to reuse and recovery, including recycling 

of waste equipment. For more information about the appropriate recycling 

methods, contact your local authority or retailer.

Содержание YT-83113





































Отзывы: