YASKAWA Varispeed f7 Скачать руководство пользователя страница 179

Страница: 179 / 202

Programming 171

Digital Inputs

H1-01

Multi-Function Digital Input
Terminal S3 Function
Selection

Terminal S3 Sel

Selects the function of terminals S3 to S8.
0: 3-wire control
FWD/REV selection for 3-wire sequence.
1: Local/Remote Selection

Closed = Local, Open = Remote.

2: Option/Inv Selection

Selects source of frequency reference and sequence.
Closed = Option Card, Open = b1-01 & b1-02.

3: Multi-Step Frequency Reference 1

Based on status of Multi-Step Reference 1 to 4 (d1-16).

4: Multi-Step Frequency Reference 2

Based on status of Multi-Step Reference 1 to 4 (d1-16).

5: Multi-Step Frequency Reference 3

Based on status of Multi-Step Reference 1 to 4 (d1-16).

6:  Jog Frequency Reference
   Closed = frequency reference from d1-17
7:  Accel/Decel Time Se1ection 1

Based on status of Accel/Decel Time Selection 1 and 2.

8:  External BaseBlock N.O.
   Closed = Output transistors forced off.
   Open = Normal operation.
9:  External BaseBlock N.C.
   Closed = Normal operation.
   Open = Output transistors forced off.
A: Acc/Dec Ramp Hold

Closed = Acceleration suspended and speed held.

B: External Overheat Alarm (OH2)

Closed = OH2 alarm.

C: Terminal A2 Enable

Closed = Terminal A2 is active.
Open = Terminal A2 is disabled.

D: V/F Control with PG Disabled

Closed = Speed feedback control disabled.

E: ASR Integral Reset

Closed = Integral reset.

F: Terminal Not Used

Terminal closure has no effect.

10: MOP Increase
Closed = frequency reference increases.
Open = frequency reference held.

Must be set in conjunction with MOP Decrease and b1-01
must be set to 1.

11: MOP Decrease

Closed = frequency reference decreases.

Open = frequency reference held.

Must be set in conjunction with MOP Increase and b1-01 must
be set to 1.

12: Forward Jog

Closed = Drive runs forward at frequency reference entered
into parameter d1-17.

13: Reverse Jog

Closed = Drive runs in reverse at frequency reference entered
into parameter d1-17.

14: Fault Reset

Closed = Resets the Drive after the fault and the run command
have been removed.

(Continued on following page).

0 to 78

H1-02

Multi-Function Digital Input
Terminal S4 Function
Selection

Terminal S4 Sel

0 to 78

Denotes that parameter can be changed when the Drive is running.

Table A.1 F7 Parameter List (Continued)

Parameter

No.

Parameter Name

Digital Operator Display

Description

Setting

Range

Factory

Setting

Control Method

V/F

Open

Loop

Vector

Flux

Vector

Содержание Varispeed f7











































































































































































































Результаты поиска

Содержание Varispeed f7

Отзывы:

Похожие инструкции для Varispeed f7

Бренды по названию

Популярные бренды

YASKAWA Varispeed f7, Руководство по программированию

Результаты поиска

Содержание Varispeed f7

Отзывы:

Похожие инструкции для Varispeed f7

Бренды по названию

Популярные бренды