YASKAWA Varispeed f7 Скачать руководство пользователя страница 156 | Manualshive

Страница: 156 / 202

background image

Programming 148

Rotational auto-tuning with the load uncoupled from the motor is strongly recommended whenever possible. Stationary auto-
tuning is used whenever it is not possible to disconnect the motor from the load. Rotational and stationary auto-tuning can be
selected only when in open loop vector or flux vector control modes (A1-02 = 2 or 3). If terminal resistance auto-tuning is
selected, only parameters T1-02 and T1-04 need to be set. Terminal Resistance auto-tuning can be selected in all control
modes (A1-02 = 0, 1, 2, or 3).

T1-02 Motor Rated Power

Setting Range:

0.00 to 650.00 kW

Factory Default: Model Dependent

Set the rated power in kilowatts (kW) of the motor attached to the Drive. If the motor nameplate lists the rated power in terms
of horsepower (HP), use the following formula to convert to kW before setting the value of T1-02:

kW = HP x 0.746

T1-03 Motor Rated Voltage

Setting Range:

0.0 to 255.0 Vac (240V Class), 0.0 to 510.0 (480V Class)

Factory Default: 240 Vac (240V Class), 460Vac (480V Class)

Set the motor rated voltage.

T1-04 Motor Rated Current

Setting Range:

Model Dependent

Factory Default: Model Dependent

Set the motor rated current (FLA) as stamped on the motor’s nameplate.

T1-05 Motor Base Frequency

Setting Range:

0.0 to 400.0 Hz

Factory Default: 60.0 Hz

Set the motor base frequency (in Hz) as stamped on the motor’s nameplate.

T1-06 Number of Motor Poles

Setting Range:

2 to 48

Factory Default: 4

Set the number of motor poles as stamped on the motor’s nameplate. If this is not found on the nameplate, use the following
formula to determine the number of motor poles

Number of Motor Poles = 120 x Frequency in Hz / RPM

Example:
An 1800 RPM, 60Hz motor is (120 x 60Hz / 1800RPM = 4) a 4 pole motor.

«
...
154
155
156
157
158
...
»

Содержание Varispeed f7











































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Varispeed f7

C1400-CO-VS-0S-I03

Бренд: NTI AG Страницы: 20

Бренд: Teac Страницы: 15

Бренд: IEF Werner Страницы: 48

Бренд: Xinje Страницы: 109

Бренд: Parker Страницы: 148

ThinkPad 43N3201

Бренд: Lenovo Страницы: 46

ThinkPad 40Y8626

Бренд: Lenovo Страницы: 58

ThinkCentre 41N5624

Бренд: Lenovo Страницы: 66

ThinkCentre 41N5626

Бренд: Lenovo Страницы: 72

ThinkPad 41N5643

Бренд: Lenovo Страницы: 46

ThinkPad 40Y8706

Бренд: Lenovo Страницы: 62

ThinkPad 40Y8710

Бренд: Lenovo Страницы: 68

Бренд: Lenovo Страницы: 70

Бренд: Lenovo Страницы: 6

Бренд: LG Страницы: 25

Бренд: LG Страницы: 16

Бренд: LG Страницы: 14

Бренд: LG Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды