YASKAWA Varispeed f7 Скачать руководство пользователя страница 192

Страница: 192 / 202

Programming 184

Torque Limit

L7-01

Forward Torque Limit

Torq Limit Fwd

Sets the torque limit value as a percentage of the motor rated
torque. Four individual quadrants can be set.

0 to 300

200%

L7-02

Reverse Torque Limit

Torq Limit Rev

0 to 300

200%

L7-03

Forward Regenerative
Torque Limit

Torq Lmt Fwd Rgn

0 to 300

200%

L7-04

Reverse Regenerative Torque
Limit

Torq Lmt Rev Rgn

0 to 300

200%

Hardware Protection

L8-01

Internal Dynamic Braking
Resistor Protection Selection

DB Resistor Prot

Selects the DB protection only when using 3% duty cycle heatsink
mount Yaskawa braking resistor. This parameter does not enable or
disable the DB function of the Drive.
0: Not Provided
1: Provided

0 to 1

L8-02

Overheat Alarm Level

OH Pre-Alarm Lvl

When the cooling fin temperature exceeds the value set in this
parameter, an overheat alarm (OH) will occur.

50 to

130

95°C

L8-03

Overheat Pre-Alarm
Operation Selection

OH Pre-Alarm Sel

Selects the Drive operation upon an OH pre-alarm detection.
0: Ramp to Stop
1: Coast to Stop
2: Fast-Stop
3: Alarm Only

0 to 3

L8-05

Input Phase Loss Protection
Selection

Ph Loss In Sel

Selects the detection of input current phase loss, power supply volt-

age imbalance, or main circuit electrostatic capacitor deterioration.

0: Disabled
1: Enabled

0 to 1

L8-07

Output Phase Loss Protection

Ph Loss Out Sel

Selects the detection of output current open-phase.

When applied motor capacity is too small for Drive capacity,

output phase loss may be detected inadvertently. In this case, set to 0.

0: Disabled

1: 1-phase Loss Detection

2: 2/3-phase Loss Detection

0 to 1

L8-09

Output Ground Fault
Detection Selection

Ground Fault Sel

Enables and disables the Drive’s output ground fault detection.
0: Disabled
1: Enabled

0 to 1

L8-10

Heatsink Cooling Fan
Operation Selection

Fan On/Off Sel

Controls the heatsink cooling fan operation.
0: Fan On-Run Mode - Fan will operate only when the Drive is

running and for L8-11 seconds after RUN is removed.

1: Fan Always On

- Cooling fan operates whenever the Drive is

powered up.)

0 to 1

L8-11

Heatsink Cooling Fan
Operation Delay Time

Fan Delay Time

This parameter sets the delay time for the cooling fan turn off after
the run command is removed when L8-10 = 0.

0 to 300

60sec

L8-12

Ambient Temperature Setting

Ambient Temp

When the Drive is installed in an ambient temperature exceeding
its rating, the Drive overload (OL2) protection level is adjusted.

45 to 60

45°C

Denotes that parameter can be changed when the Drive is running.

Table A.1 F7 Parameter List (Continued)

Parameter

No.

Parameter Name

Digital Operator Display

Description

Setting

Range

Factory

Setting

Control Method

V/F

Open

Loop

Vector

Flux

Vector

Output torque

Positive torque

Reverse

Negative torque

No. of

motor

rotations

Regen. state

Forward

Содержание Varispeed f7











































































































































































































Результаты поиска

Содержание Varispeed f7

Отзывы:

Похожие инструкции для Varispeed f7

Бренды по названию

Популярные бренды

YASKAWA Varispeed f7, Руководство по программированию

Результаты поиска

Содержание Varispeed f7

Отзывы:

Похожие инструкции для Varispeed f7

Бренды по названию

Популярные бренды