manualshive.com logo in svg

YASKAWA Varispeed f7, Руководство по программированию

Технический мануал для YASKAWA Varispeed F7 доступен для скачивания бесплатно на сайте manualshive.com. Подробное описание и инструкции по установке и эксплуатации данного продукта помогут вам использовать его наилучшим образом. Убедитесь скачать руководство перед началом работы с устройством.

Поделиться
Скачать
background image

Programming  76

Function: V/f Control with PG Disabled

Setting: D

PG feedback input can be disabled while the Drive is running when this function is selected. However, the speed control 
integral value (C5-05) is held until the run command is removed.

Open:

PG feedback control enabled (closed loop)

Closed:

PG feedback control disabled (open loop)

This function is available only during V/f control with PG feedback (A1-02 = 1).

Function: Terminal Not Used

Setting: F

Any digital input programmed as Term Not Used (H1-0x= F) will have no function assigned to it and it’s OPEN/CLOSED 
state will not matter to the Drive’s operation.

Function: MOP Increase

Setting: 10

Function: MOP Decrease

Setting: 11

Using two digital inputs, the Drive can operate with the same type of functionality as a motor operated potentiometer (MOP). 
One digital input can be programmed as an MOP Increase input (H1-0x= 10) and another digital input can be programmed as 
an MOP Decrease input (H1-0x= 11). This MOP functionality is also commonly referred to as Floating Point Control, 
Incremental Control or UP and DOWN Control since closing the MOP Increase input will cause the frequency reference to 
increase and closing the MOP Decrease input will cause the frequency reference to decrease.

If both the MOP Increase and the MOP Decrease are closed or open simultaneously, the speed will command will not change. 
The frequency reference will change at the active acceleration or deceleration rate. 

MOP Increase cannot be programmed without also programming the MOP Decrease (or vice-versa) else an OPE03 fault will 
occur. Setting the MOP Increase/Decrease function while the Acc/Dec Ramp Hold function is programmed into other digital 
inputs will also cause an OPE03 fault.

Once the MOP function is programmed the preset speeds are disabled and the analog frequency reference input becomes a  
potential frequency reference lower limit. The lower limit of the MOP function is the greater of the analog frequency reference 
and the programmed frequency reference lower limit (d2-03). Once a Run command is issued the Drive will accelerate 
immediately to the lower limit. The upper limit will be the Frequency Reference Upper Limit (d2-01), if used, otherwise it will 
be the maximum output frequency (E1-04).

The status of the d4-01 parameter (MOP Reference Memory) will affect the performance of the Drive after power is cycled to 
the Drive and a fresh Run command is issued. If d4-01= “0: Disabled”, the Run command will cause the Drive to ramp to the  
frequency reference lower limit. However, if d4-01= “1: Enabled”, the Run command will cause the Drive to ramp to the last 
frequency referenced by the MOP function before the Run command was removed and the power cycled. Even if d4-01=    “1: 
Enabled”, the previous frequency reference can be reset to the frequency reference lower limit automatically by closing either 
the UP or Down input without having a Run command active.

IMPORTANT

Be sure to set b1-01= “1: Terminals”, (frequency reference Source =Terminals) if the MOP function is to be 
used. If b1-01= “0: Operator”, then the MOP is disabled even if it is programmed. The Jog inputs have priority 
over the MOP function.

Содержание Varispeed f7











































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Varispeed f7

Nastec MIDA 203 Installation And Use Manual preview
MIDA 203
Бренд: Nastec Страницы: 28
BMG CRUSADER ONE 72H-033 Instruction Manual preview
CRUSADER ONE 72H-033
Бренд: BMG Страницы: 3
Lenze E94AZCDM030 Mounting Instructions preview
E94AZCDM030
Бренд: Lenze Страницы: 72
Tsino Dynatron EtherCAT CoolDrive RC Series User Manual preview
EtherCAT CoolDrive RC Series
Бренд: Tsino Dynatron Страницы: 278
Aiwa BZG-2 Service Manual preview
BZG-2
Бренд: Aiwa Страницы: 26
Delixi CDI-SPD Series Manual preview
CDI-SPD Series
Бренд: Delixi Страницы: 33
Becker C01a Assembly And Operating Instructions Manual preview
C01a
Бренд: Becker Страницы: 28
Becker E12a Assembly And Operating Instructions Manual preview
E12a
Бренд: Becker Страницы: 32
Becker E01 Series Assembly And Operating Instructions Manual preview
E01 Series
Бренд: Becker Страницы: 32
DVS DS Series Manual preview
DS Series
Бренд: DVS Страницы: 16
Asus 48x/24x/52x CD-RW Drive CRW-4824A User Manual preview
48x/24x/52x CD-RW Drive CRW-4824A
Бренд: Asus Страницы: 26
Asus 24x/10x/40x CD-RW Drive CRW-2410S User Manual preview
24x/10x/40x CD-RW Drive CRW-2410S
Бренд: Asus Страницы: 24
Asus 40x/12x/48x CD-RW Drive CRW-4012A User Manual preview
40x/12x/48x CD-RW Drive CRW-4012A
Бренд: Asus Страницы: 26
Asus 48x/16x/48x CD-RW Drive CRW-4816A User Manual preview
48x/16x/48x CD-RW Drive CRW-4816A
Бренд: Asus Страницы: 26
Asus CRW-2410A User Manual preview
CRW-2410A
Бренд: Asus Страницы: 26
Asus CRW-5232AS User Manual preview
CRW-5232AS
Бренд: Asus Страницы: 40
Asus CRW-5232A User Manual preview
CRW-5232A
Бренд: Asus Страницы: 26
Asus Network Device CRW-3212A User Manual preview
Network Device CRW-3212A
Бренд: Asus Страницы: 18

Бренды по названию

Популярные бренды

Загрузить еще бренды