YASKAWA Varispeed f7 Скачать руководство пользователя страница 100 | Manualshive

Страница: 100 / 202

background image

Programming 92

Function: Timer Output
Setting: 12

This Timer function, that is built into the Drive, is independent of the rest of the Drive operation, i.e. there is no requirement
for a Run command for the timer to operate. A Timer digital output will close b4-01 seconds after a digital input configured as
Timer Input (H1-0x= 18) closes and remains closed. The Timer digital output will remain closed for b4-02 seconds after the
Timer digital input opens and remains open.

Refer to the descriptions of parameters b4-01 and b4-02 for a timing chart of the Timer function.

Function: Fref/Fout Agree 2
Setting: 13

The “Fref/Fout Agree 2” output will close whenever the actual output frequency is within the Speed Agree Width (L4-04) of
the current frequency reference regardless of the direction.

Function: Fref/Fset Agree 2
Setting: 14

The “Fref/Set Agree 2” output will close whenever the actual output frequency and the frequency reference are within the
Speed Agree Width (L4-04) of the programmed Speed Agree Level (L4-03). This Fref/Fset Agree 2 output is direction
sensitive according to the direction programmed in L4-03.

Function: Freq Detect 3
Setting: 15

A “Freq Detect 3” output will be closed whenever the output frequency is equal to or below the value of the programmed
Speed Agree Level (L4-03). The Speed Agree Width (L4-04) is the hysteresis to the Freq Detect 3 function. Whenever the
output frequency approaches the Speed Agree Level while accelerating it will need to be equal to or exceed the Speed Agree
Level (L4-03) plus the Speed Agree Width (L4-04) before the Freq Detect 3 output will energize.

As the output frequency approaches the Speed Agree Level while decelerating, the Freq Detect 3 output will de-energize
exactly at the Speed Agree Level.

This Freq Detect 3 output is direction sensitive according to the direction programmed in L4-03.

Function: Frequency Detection 4
Setting: 16

A Frequency Detect 4 output will be closed whenever the output frequency is equal to or above the value of the programmed Speed
Agree Level (L4-03). The Speed Agree Width (L4-04) is the hysteresis to the Freq Detect 4 function. Whenever the output frequency
approaches the Speed Agree Level (L4-03) while accelerating it will de-energize exactly at the Speed Agree Level.

As the output frequency approaches the Speed Agree Level while decelerating, the Freq Detect 4 output will
de-energize when the output frequency is equal to or below the Speed Agree Level (L4-03) minus the Speed Agree Width (L4-04).

This Freq Detect 3 output is direction sensitive according to the direction programmed in L4-03.

«
...
98
99
100
101
102
...
»

Содержание Varispeed f7











































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Varispeed f7

Penta Power KBRG-212D

Бренд: KB Electronics Страницы: 17

Бренд: AMX Страницы: 2

Бренд: Philips Страницы: 2

Бренд: Philips Страницы: 7

Бренд: Philips Страницы: 56

Бренд: Philips Страницы: 64

Бренд: Philips Страницы: 80

Бренд: Philips Страницы: 100

Бренд: Philips Страницы: 116

Бренд: Leeson Страницы: 44

ILBLP CP10 HE SD

Бренд: IOTA Страницы: 8

SubDrive Connect Plus SDCP-SUB1023

Бренд: Franklin Electric Страницы: 12

Allen-Bradley PowerFlex 700AFE

Бренд: Rockwell Automation Страницы: 186

Zip 250MB Parallel Port Drive

Бренд: Iomega Страницы: 24

Бренд: Iomega Страницы: 36

Бренд: Mitsubishi Страницы: 219

Бренд: Kanguru Страницы: 20

PRIMAT-E Kompakt 190

Бренд: HAUTAU Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды