YASKAWA Varispeed f7 Скачать руководство пользователя страница 201 | Manualshive

Страница: 201 / 202

background image

Drives Technical Support in USA and Canada

Technical Support for Inverters and Drives is available by phone as follows:
Normal:

Monday through Friday during the hours of 8 a.m. to 5:00 p.m. C.S.T.

Emergency:

After normal hours, 7 days a week including weekends and holidays

To contact Drives Technical Support, please call 1-800-YASKAWA (927-5292).
From the menu, dial 2 for Inverter and Drive Products, then 5 for Technical Support.

Drives Technical Support can also be reached by e-mail at

[email protected]

.

Support information, such as technical manuals, FAQs, instruction sheets and software downloads are available at our website,

www.drives.com

.

When calling for technical support, please have the following materials available:

•

The appropriate Technical Manual in hand because the support associate may refer to this

•

Complete nameplate information from the drive and the motor.

(Confirm that Drive Nameplate Output amps is greater than Motor Nameplate amps)

•

Α

list of your parameter settings

•

A sketch of the electrical powertrain, from AC line to motor, including filters and disconnects

Field Service, Start Up Assistance, Factory Repair, Replacement Parts, and Other Support

Contact Drives Technical Support for help with any of these needs.

Technical Training

Training is conducted at Yaskawa training centers, at customer sites, and via the internet.
For information, visit

www.drives.com

or call 1-800-YASKAWA (927-5292).

From the phone menu, dial 2 for Inverter and Drive Products, then 4 for Product Training.

Support in Other Countries

Yaskawa is a multi-national company with offices and service representation around the world.
To obtain support, always contact the local distributor first for guidance and assistance.
Contact the closest Yaskawa office listed for further assistance.

«
...
199
200
201
202
»

Содержание Varispeed f7











































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Varispeed f7

Бренд: Bardac Страницы: 62

GA700 GA700 Series

Бренд: YASKAWA Страницы: 32

Бренд: Kenwood Страницы: 2

Бренд: Kenwood Страницы: 2

Бренд: Leadshine Страницы: 16

Бренд: Leadshine Страницы: 15

Бренд: Topcnc Страницы: 104

Бренд: Dover Страницы: 26

Бренд: ZIEHL-ABEGG Страницы: 28

Бренд: Vacon Страницы: 28

Бренд: Danfoss Страницы: 16

Бренд: Lenze Страницы: 199

Бренд: YASKAWA Страницы: 378

Бренд: Leroy-Somer Страницы: 124

Бренд: Danfoss Страницы: 2

VLT Panduan Cepat

Бренд: Danfoss Страницы: 25

Бренд: ABB Страницы: 2

Бренд: Grundfos Страницы: 68

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды