YASKAWA CC-Link Скачать руководство пользователя | Manualshive

Страница: 17 / 61

background image

5 Installation Procedure

YASKAWA ELECTRIC

TOBP C730600 83C YASKAWA AC Drive Option SI-C3 Installation Manual

17

Install the Option

Remove the front covers of the drive before you install the option.

Refer to the drive manual for information about how to remove the front covers. Different

drive sizes have different cover removal procedures.

You can only install this option into the

CN5-A

connector on the drive control board.

DANGER!

Electrical Shock Hazard. Do not inspect, connect, or disconnect any wiring while the drive is

energized. Failure to comply will cause death or serious injury. Before servicing, disconnect all power to the

equipment and wait for at least the time specified on the warning label. The internal capacitor remains

charged even after the drive is de-energized. The charge indicator LED will extinguish when the DC bus

voltage is below 50 Vdc. When all indicators are OFF, measure for unsafe voltages to confirm the drive is

safe.

1.

Shut off power to the drive, wait the appropriate amount of time for voltage to
dissipate, then remove the keypad (D) and front covers (C, F).

Refer to the manual packaged with the drive for details on keypad and cover

removal.

NOTICE:

Damage to Equipment. Observe proper electrostatic discharge (ESD) procedures when handling

the option, drive, and circuit boards. Failure to comply could cause ESD damage to circuitry.

Figure 6

Figure 6 Remove the Keypad, Front Cover, and Terminal Cover

C

D

F

TOBP_C730600_83C_3_0_E.fm 17 ページ２０１８年１０月２４日　水曜日　午後５時５９分

«
...
15
16
17
18
19
...
»

Содержание CC-Link






























































Отзывы:

Нет отзывов

Похожие инструкции для CC-Link

Бренд: Warren Controls Страницы: 16

Бренд: Ebyte Страницы: 35

Бренд: FAAC Страницы: 60

Бренд: FAAC Страницы: 12

Бренд: FAAC Страницы: 44

Бренд: FAAC Страницы: 44

Бренд: FAAC Страницы: 8

Бренд: FAAC Страницы: 60

Бренд: FAAC Страницы: 14

Бренд: FAAC Страницы: 68

Бренд: FAAC Страницы: 16

Бренд: tams elektronik Страницы: 60

Бренд: Parker Страницы: 44

Бренд: YOKOGAWA Страницы: 2

ALICAT SCIENTIFIC PC

Бренд: Halma Страницы: 2

ALICAT SCIENTIFIC PCD

Бренд: Halma Страницы: 46

Бренд: Vag Страницы: 15

Total Access 351 Series

Бренд: ADTRAN Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды