YASKAWA CC-Link Скачать руководство пользователя

Страница: 52 / 61

9 Troubleshooting

YASKAWA ELECTRIC

TOBP C730600 83C YASKAWA AC Drive Option SI-C3 Installation Manual

Fault LED Display on Option Side

Defining Option LED States

Figure 26

Figure 26 Option LED Labels

Table 19 LED Display

Note:

If communication stops while the drive is running, check the following:



Is the option properly installed?



Is the communication line properly connected to the option? Is it loose?



Is the controller program working? Has the controller/PLC CPU stopped?



Did a momentary power loss interrupt communications?

Faults that Occur with a Single Drive

The example below demonstrates how to read the LED display on the front cover of the

drive to determine the cause of a fault and corrective action.

Figure 27

Figure 27 Connecting a Single Drive

L.RUN

Switches on when data is being received normally. Turns off when the
receive data is interrupted.

Lights whenever data is sent.

Light whenever data is received.

L.ERR

Lights when a CRC or abort error occurs.

L.ERR

L.RUN
SD

GA700 and GA800 Label

1000-Series Label

Power
supply

CPU

Master

device

Station 1

Drive

CC-Link

Option

TOBP_C730600_83C_3_0_E.fm 52 ページ２０１８年１０月２４日　水曜日　午後５時５９分

Содержание CC-Link






























































Результаты поиска

Содержание CC-Link

Отзывы:

Похожие инструкции для CC-Link

Бренды по названию

Популярные бренды

YASKAWA CC-Link, Руководство по установке

Результаты поиска

Содержание CC-Link

Отзывы:

Похожие инструкции для CC-Link

Бренды по названию

Популярные бренды