YASKAWA CC-Link Скачать руководство пользователя

Страница: 16 / 61

5 Installation Procedure

YASKAWA ELECTRIC

TOBP C730600 83C YASKAWA AC Drive Option SI-C3 Installation Manual

Procedure A

This section shows the procedure to install and wire the option on a 1000-series drive.

Prepare the Drive for the Option

1. Correctly wire the drive as specified by the manual packaged with the drive.

2. Make sure that the drive functions correctly.

Refer to

Figure 5

for an exploded view of the drive with the option and related components

for reference in the installation procedure.

Figure 5

Figure 5 Drive Components with Option

A – Insertion point for CN5

connector

I – Ground wire

J – Option modular connector CN1

B – SI-C3 option

K – Drive grounding terminal (FE)

C – Drive front cover

L – Connector CN5-A

D – Keypad

M – Connector CN5-B

(Not available for communication option
installation.)

E – LED label

F – Drive terminal cover

G – Removable tabs for wire

routing

N – Connector CN5-C

(Not available for communication option
installation.)

H – Included screws

L.EER

L.RUN
SD

TOBP_C730600_83C_3_0_E.fm 16 ページ２０１８年１０月２４日　水曜日　午後５時５９分

Содержание CC-Link






























































Результаты поиска

Содержание CC-Link

Отзывы:

Похожие инструкции для CC-Link

Бренды по названию

Популярные бренды

YASKAWA CC-Link, Руководство по установке

Результаты поиска

Содержание CC-Link

Отзывы:

Похожие инструкции для CC-Link

Бренды по названию

Популярные бренды