YASKAWA CC-Link Скачать руководство пользователя страница 55

Страница: 55 / 61

9 Troubleshooting

YASKAWA ELECTRIC

TOBP C730600 83C YASKAWA AC Drive Option SI-C3 Installation Manual

Table 21 LED Fault Display for CC-Link Option with Multiple Drives



: On /



: Flashing /

: Off /

∗

: Either on or off

LED Status

Cause

Corrective Action

Master

Remote Device Addresses

(CC-Link Option)

Station 1

Station 2

Station 3

TIME



LINE



or
TIME

LINE



L.RUN



L.ERR

L.RUN



L.ERR

L.RUN



L.ERR

Normal operation

–

L.RUN

L.ERR

L.RUN



L.ERR

L.RUN



L.ERR

The CC-Link Option for the
first station is not properly
installed.



Make sure the CC-Link

Option and drive are
connected together properly.

L.RUN

∗

L.ERR

∗

L.RUN



L.ERR

L.RUN



L.ERR

The CC-Link Option for the
first station is damaged
(most often all LEDs are
out).

Note:

Sometimes an

error will appear

on the drive’s

keypad



Replace the CC-Link

Option.

L.RUN



L.ERR

L.RUN

∗

L.ERR

L.RUN

∗

L.ERR

Because L.RUN after Station
2 is off, either the comm.
line between Station 1 and
Station 2 is disconnected, or
the connector has come
loose.

Make sure components are
connected correctly, using
the LEDs as a guide to
indicate a proper connection.

L.RUN

∗

L.ERR

L.RUN

∗

L.ERR

L.RUN

∗

L.ERR

Communication cable has
short-circuited



Look for any

short-circuits along the
communication lines and fix
any problems.

L.RUN

∗

L.ERR

∗

L.RUN

∗

L.ERR

∗

L.RUN

∗

L.ERR

∗

Communication cable is not
wire properly



Check the wiring for the

CC-Link Option connector
and fix and mistakes.

L.RUN

∗



L.ERR

L.RUN



L.ERR

L.RUN

∗



L.ERR

The CC-Link Options for
Station 1 and Station 3 have
been assigned the same
address.



Enter the correct station

address and cycle power.

L.RUN



L.ERR

L.RUN



L.ERR

L.RUN



L.ERR

The CC-Link Option for
Station 2 has a different
communication speed setting
than the master device.



Set the correct

communication speed and
cycle power.

TOBP_C730600_83C_3_0_E.fm 55 ページ２０１８年１０月２４日　水曜日　午後５時５９分

Содержание CC-Link






























































Результаты поиска

Содержание CC-Link

Отзывы:

Бренды по названию

Популярные бренды

YASKAWA CC-Link, Руководство по установке

Результаты поиска

Содержание CC-Link

Отзывы:

Бренды по названию

Популярные бренды