YASKAWA CC-Link Скачать руководство пользователя

Страница: 51 / 61

9 Troubleshooting

YASKAWA ELECTRIC

TOBP C730600 83C YASKAWA AC Drive Option SI-C3 Installation Manual

Alarms

Keypad Display

Alarm Name

AEr

Station Address Error
Option is set to an address outside the allowable setting range.

Cause

Possible Solution

Alarm

(H2-



= 10)

CC-Link Option is set to an
address outside the
allowable setting range.

Set F6-10 to an address within the specified range.

YES

Keypad Display

Alarm Name

CALL

Serial Communication Transmission Error
Communication is not established.

Cause

Possible Solution

Alarm

(H2-



= 10)

Communication wiring is
faulty.

• Check for wiring errors.
• Correct the wiring.

YES

An existing short circuit or
communications
disconnection

Check disconnected cables and short circuits and repair as needed.

Programming error on the
master side.

Check communications at start-up and correct programming errors.

Communication circuitry is
damaged.

• Perform a self-diagnostics check.
• If the problem continues, replace either the control board or the

entire drive. For instructions on replacing the control board, contact
Yaskawa or a Yaskawa representative.

Termination resistor of the
MEMOBUS/Modbus
communications is not
enabled.

Set DIP switch S2 to the ON position to enable the termination
resistor on a drive located at the end of a network line.

Keypad Display

Alarm Name

CyPo

Cycle Power to Active Parameters
Comm. Option Parameter Not Upgraded

Cause

Possible Solution

Alarm

(H2-



= 10)

Although F6-15 = 1 [Comm.
Option Parameters Reload =
Reload Now], the drive does
not update the
communication option
parameters.

Re-energize the drive to update the communication option
parameters.
Note: If the option software version is not compatible or if you install
an incorrect option to the drive, it will trigger an alarm.

YES

TOBP_C730600_83C_3_0_E.fm 51 ページ２０１８年１０月２４日　水曜日　午後５時５９分

Содержание CC-Link






























































Результаты поиска

Содержание CC-Link

Отзывы:

Похожие инструкции для CC-Link

Бренды по названию

Популярные бренды

YASKAWA CC-Link, Руководство по установке

Результаты поиска

Содержание CC-Link

Отзывы:

Похожие инструкции для CC-Link

Бренды по названию

Популярные бренды