Yamaha F30 Скачать руководство пользователя

Страница: 5 / 120

Table of contents

control or tiller handle..................... 32

cowling ........................................... 32

Variable trolling RPM switches ......... 33
Trim tab with anode........................... 33
Tilt lock mechanism........................... 34
Tilt support knob................................ 34
Cowling lock lever ............................. 34
Flushing device ................................. 34
Fuel filter/Water separator................. 35
Alert indicator ................................... 35

Instruments and indicators ............ 36

Indicators ....................................... 36

Low oil pressure-alert indicator ......... 36
Overheat-alert indicator..................... 36

Digital tachometer .......................... 36

Tachometer ....................................... 37
Trim meter ......................................... 37
Hour meter ........................................ 37
Low oil pressure-alert indicator ......... 37
Overheat-alert indicator..................... 38

Digital speedometer ....................... 38

Speedometer..................................... 38
Fuel gauge ........................................ 38
Trip meter / Clock / Voltmeter............ 39
Fuel level-alert indicator .................... 40
Low battery voltage-alert indicator .... 40

6Y8 Multifunction meters................ 40

Engine control system.................... 44

Alert system ................................... 44

Overheat alert.................................... 44
Low oil pressure alert ........................ 44

Installation ....................................... 46

Installation ...................................... 46

Mounting the outboard motor ............ 46

Operation ......................................... 48

First-time operation ........................ 48

Fill engine oil ..................................... 48

Breaking in engine............................. 48
Getting to know your boat ................. 48

Checks before starting engine ....... 48

system............................................ 51

Battery ............................................... 52

Filling fuel....................................... 52
Operating engine ........................... 55

Sending fuel (portable tank) .............. 56
Starting engine .................................. 58

Checks after starting engine .......... 61

Cooling water .................................... 61

Warming up engine........................ 61

Manual start and electric start

models ........................................... 61

Checks after engine warm up ........ 61

Shifting .............................................. 61
Stop switches .................................... 61

Shifting ........................................... 62
Stopping boat................................. 63
Trolling ........................................... 63

Adjusting trolling speed ..................... 63

Stopping engine............................. 64

Procedure.......................................... 64

Trimming outboard motor............... 66

Adjusting trim angle (Power trim and

tilt) .................................................. 67

Adjusting trim angle for hydro tilt

models ........................................... 67

Adjusting boat trim............................. 68

Tilting up and down........................ 69

Procedure for tilting up (hydro tilt

models) .......................................... 69

Procedure for tilting up (power trim

and tilt models)............................... 70

6BG-9-3F-E0.book 2 ページ２０１８年１１月１日　木曜日　午後５時１分

Yamaha

Motor

Corporation

Содержание F30

























































































































Результаты поиска

Содержание F30

Отзывы:

Похожие инструкции для F30

Бренды по названию

Популярные бренды

Yamaha F30, Руководство пользователя

Результаты поиска

Содержание F30

Отзывы:

Похожие инструкции для F30

Бренды по названию

Популярные бренды