manualshive.com logo in svg

Yamaha F30, Руководство пользователя

Поделиться
Скачать
Yamaha F30 Скачать руководство пользователя страница 56

Operation

50

turns to the fully closed position.

Look for loose or damaged connections of
the throttle and shift cables.

Remote control models:

Turn the steering wheel full-right and full-
left. Make sure operation is smooth and
unrestricted throughout the whole range
with no binding or excessive free play.

Operate the throttle levers several times to
make sure there is no hesitation in their
travel. Operation should be smooth over
the complete range of motion, and each le-
ver should return completely to the idle po-
sition.

Look for loose or damaged connections of
the throttle and shift cables.

EMU36484

Engine shut-off cord (lanyard)

Inspect the engine shut-off cord and clip for
damage, such as cuts, breaks, and wear.

EMU40994

Engine oil

1. Place the outboard motor in a vertical

position (not tilted). 

NOTICE:

 If the out-

board motor is not level, the oil level
indicated on the oil dipstick may not
be accurate.

 [ECM01862]

2. Remove the oil dipstick and wipe it

clean.

3. Insert the oil dipstick completely and re-

move it again.

4. Check that the oil level on the oil dipstick

is between the upper and lower marks.
Consult your Yamaha dealer if the oil
level is not at the proper level or if it ap-
pears milky or dirty.

EMU27154

Engine

Check the engine and engine mounting.

Look for loose or damaged fasteners.

Check the propeller for damage.

Check for engine oil leaks.

EMU36494

Flushing device

Check that the flushing device’s garden hose

1. Clip
2. Engine shut-off cord (lanyard)

ZMU06

8

73

1

2

1. Oil dipstick

1. Lower mark
2. Oil dipstick
3. Upper mark

1

ZMU06400

1

3

2

ZMU05091

6BG-9-3F-E0.book  50 ページ  ２０１８年１１月１日　木曜日　午後５時１分

©2020 

Yamaha 

Motor 

Corporation

Содержание F30

























































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды