Yamaha F30 страница 40 Скачать руководство пользователя

Страница: 40 / 120

Components

EMU26313

Tilt lock mechanism

The tilt lock mechanism is used to prevent
the outboard motor from lifting out of the wa-
ter when in reverse gear.

To lock it, set the tilt lock lever in the “

”

(lock) position. To release, push the tilt lock
lever in the “ ” (release) position.

EMU26323

Tilt support knob

To keep the outboard motor in the tilted up
position, push the tilt support knob under the
swivel bracket.

NOTICE

ECM00661

Do not use the tilt support lever or knob
when trailering the boat. The outboard

motor could shake loose from the tilt sup-
port and fall. If the motor cannot be
trailered in the normal running position,
use an additional support device to se-
cure it in the tilt position.

EMU39264

Cowling lock lever

The cowling lock lever(s) is used to secure
the top cowling.

EMU26464

Flushing device

This device is used to clean the cooling wa-
ter passages of the motor using a garden
hose and tap water.

TIP:

For details on usage, see page 79.

Bolt tightening torque:

18 N·m (1.8 kgf·m, 13 lb·ft)

1. Tilt lock lever

ZMU06395

ZMU06396

1. Cowling lock lever(s)

1. Flushing device

ZMU08532

ZMU0639

6BG-9-3F-E0.book 34 ページ２０１８年１１月１日　木曜日　午後５時１分

Yamaha

Motor

Corporation

Содержание F30

























































































































Результаты поиска

Содержание F30

Отзывы:

Похожие инструкции для F30

Бренды по названию

Популярные бренды

Yamaha F30, Руководство пользователя

Результаты поиска

Содержание F30

Отзывы:

Похожие инструкции для F30

Бренды по названию

Популярные бренды