background image

Operation

49

dent could occur.

NOTICE

ECM00121

Do not start the engine out of water. Over-
heating and serious engine damage can
occur.

EMU36422

Fuel level

Be sure you have plenty of fuel for your trip.
A good rule is to use 1/3 of your fuel to get to
the destination, 1/3 to return, and to keep 1/3
as an emergency reserve. With the boat lev-
el on a trailer or in the water, turn the key to

” (on) and check the fuel level. For fuel

filling instructions, see page 52.

EMU36573

Remove the top cowling

For the following checks, remove the top
cowling from the bottom cowling. To remove
the top cowling, release the cowling lock le-
ver and lift off the top cowling.

EMU36443

Fuel system

WARNING

EWM00061

Gasoline and its vapors are highly flam-
mable and explosive. Keep away from
sparks, cigarettes, flames, or other sourc-
es of ignition.

WARNING

EWM00911

Leaking fuel can result in fire or explo-
sion.

Check for fuel leakage regularly.

If any fuel leakage is found, the fuel
system must be repaired by a qualified
mechanic. Improper repairs can make
the outboard unsafe to operate.

EMU36453

Check for fuel leaks

Check for fuel leaks or gasoline fumes in
the boat.

Check for fuel leakage from the fuel sys-
tem.

Check the fuel tank and fuel lines for
cracks, swellings, or other damage.

EMU36472

Check the fuel filter

Check that the fuel filter is clean and free of
water. If enough water to raise the float ring
is found in the fuel, or if a significant amount
of debris is found, the fuel tank should be
checked and cleaned by a Yamaha dealer.

EMU36903

Controls

Tiller handle models:

Move the tiller handle fully to the left and
right to make sure operation is smooth.

Turn the throttle grip from the fully closed
to the fully open position. Make sure that it
turns smoothly and that it completely re-

ZMU06085

ZMU06399

6BG-9-3F-E0.book  49 ページ  2018年11月1日 木曜日 午後5時1分

©2020 

Yamaha 

Motor 

Corporation

Содержание F30

























































































































Отзывы: