Yamaha F30 Скачать руководство пользователя | Manualshive

Страница: 58 / 120

background image

Operation

52

switches to check that all switches work.

3. Tilt the outboard motor up and check

that the trim and tilt rod is pushed out
completely.

4. Check that the trim and tilt rod is free of

corrosion or other flaws.

5. Tilt the outboard motor down. Check that

the trim and tilt rod operates smoothly.

EMU36585

Battery

Check the battery’s charge. If your boat is
equipped with a Yamaha digital speedome-
ter, the voltmeter and low battery alert func-
tions will help you monitor the battery’s
charge. A battery in good condition will pro-
vide a minimum of 12 volts. Check that the
battery connections are clean, secure and
covered by insulating covers. The electrical
connections of the battery and cables must
be clean and properly connected or the bat-
tery will not start the engine.
If the battery needs charging, consult your
Yamaha dealer or the battery manufacturer’s
instructions.

EMU48130

Filling fuel

WARNING

EWM01831



Gasoline and its vapors are highly flam-

mable and explosive. Always refuel ac-
cording to this procedure to reduce the
risk of fire and explosion.



Gasoline is poisonous and can cause
injury or death. Handle gasoline with
care. Never siphon gasoline by mouth.
If you should swallow some gasoline or
inhale a lot of gasoline vapor, or get
some gasoline in your eyes, see your
doctor immediately. If gasoline spills
on your skin, wash with soap and wa-
ter. If gasoline spills on your clothing,
change your clothes.

Before refueling, check the following points:



Ensure the engine is stopped.



Securely moor the boat in a well-ventilated
area and stop the engine. If the boat is
trailered, make sure that it is stable.



Do not smoke and keep away from sparks,
flames, static electric discharge, or other
sources of ignition.



If you use a portable container to store and
dispense fuel, only use a locally approved
GASOLINE container.



To prevent electrostatic sparks, discharge
any built-up static electricity from your
body before refueling.

When using the portable fuel tank “A”, fill the
fuel tank according to the following proce-
dure.

1. Trim and tilt rod

1

ZMU06402

ZMU07595

å

6BG-9-3F-E0.book 52 ページ２０１８年１１月１日　木曜日　午後５時１分

©2020

Yamaha

Motor

Corporation

«
...
56
57
58
59
60
...
»

Содержание F30

























































































































Отзывы:

Нет отзывов

Похожие инструкции для F30

Бренд: fadini Страницы: 32

Бренд: Hailo Страницы: 22

Бренд: Biostar Страницы: 53

Бренд: Safran Страницы: 26

Side-Power SEP IP Series

Бренд: SLEIPNER MOTOR AS Страницы: 28

Бренд: Ublox Страницы: 23

1stMainboard VG33

Бренд: FIC Страницы: 38

Бренд: Mercury Страницы: 41

AR0140CS2M00AUEAH3-GEVB

Бренд: ON Semiconductor Страницы: 5

Бренд: Phytec Страницы: 128

Бренд: Sapphire Audio Страницы: 50

Бренд: Biostar Страницы: 47

MITX-DNV0 Series

Бренд: Quanmax Страницы: 84

Бренд: Gigabyte Страницы: 17

Бренд: Gan Systems Страницы: 28

Advance 10T Series

Бренд: QDI Страницы: 74

Бренд: Abit Страницы: 72

Бренд: IEI Technology Страницы: 11

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды