Yamaha F30 Скачать руководство пользователя страница 50

Страница: 50 / 120

Engine control system

EMU26806

Alert system

NOTICE

ECM00093

Do not continue to operate the engine if
an alert device has activated. Consult
your Yamaha dealer if the problem cannot
be located and corrected.

EMU43754

Overheat alert

This engine has an overheat-alert device. If
the engine temperature rises too high, the
alert device will activate.



The engine speed will automatically de-
crease to 2000–3500 r/min.



The overheat-alert indicator will light or
blink (if equipped).



The buzzer will sound (if equipped on the
tiller handle, remote control box, or main
switch panel).

If the alert system has activated, stop the en-
gine and check the cooling water inlets:



Check trim angle to be sure that the cool-
ing water inlet is submerged.



Check the cooling water inlet for clogging.

EMU26869

Low oil pressure alert

If the oil pressure drops too low, the alert de-
vice will activate.



The engine speed will automatically de-
crease to about 2000–3500 r/min.

ZMU04227

ZMU03025

ZMU02630

6BG-9-3F-E0.book 44 ページ２０１８年１１月１日　木曜日　午後５時１分

Yamaha

Motor

Corporation

Содержание F30

























































































































Результаты поиска

Содержание F30

Отзывы:

Бренды по названию

Популярные бренды

Yamaha F30, Руководство пользователя

Результаты поиска

Содержание F30

Отзывы:

Бренды по названию

Популярные бренды