Yamaha F30 Скачать руководство пользователя | Manualshive

Страница: 43 / 120

background image

Instruments and indicators

37

EMU36051

Tachometer

The tachometer displays engine speed in
hundreds of revolutions per minute (r/min).
For example, if the tachometer display reads
“22” then the engine speed is 2200 r/min.

EMU26622

Trim meter

This meter shows the trim angle of your out-
board motor.



Memorize the trim angles that work best
for your boat under different conditions.
Adjust the trim angle to the desired using
the power trim and tilt switch.



If the trim angle of your motor exceeds the
trim operating range, the top segment on
the trim meter display will blink.

EMU26652

Hour meter

This meter shows the number of hours the
engine has been run. It can be set to show
the total number of hours or the number of
hours for the current trip. The display can
also be turned on and off.

To change the display format, press the
“

” (mode) button. The display can show

total hours or trip hours, or turn off.
To reset the trip hours, simultaneously press
the “

” (set) and “

” (mode) buttons for

more than 1 second while the trip hours are
displayed. This resets the trip counter to 0
(zero).
The total number of hours the engine has
been run cannot be reset.

EMU26526

Low oil pressure-alert indicator

If oil pressure drops too low, the alert indica-
tor will start to blink. For further information,
see page 44.

NOTICE

ECM00024



Do not continue to run the engine if the
low oil pressure-alert indicator is on
and the engine oil level is lower. Seri-
ous engine damage will occur.



The low oil pressure-alert indicator
does not indicate the engine oil level.
Use the oil dipstick to check the oil lev-
el. For further information, see page 50.

ZMU01740

ZMU01741

6BG-9-3F-E0.book 37 ページ２０１８年１１月１日　木曜日　午後５時１分

©2020

Yamaha

Motor

«
...
41
42
43
44
45
...
»

Содержание F30

























































































































Отзывы:

Нет отзывов

Похожие инструкции для F30

Бренд: P&E Microcomputer Systems Страницы: 59

ASC Bridge Board

Бренд: Lattice Semiconductor Страницы: 25

Бренд: Navia Страницы: 26

Бренд: Biostar Страницы: 43

Бренд: MediaQ Страницы: 25

Бренд: Avalue Technology Страницы: 75

Бренд: Shuttle Страницы: 81

Бренд: Honda Страницы: 152

880GM-LE - V1.0

Бренд: ASROCK Страницы: 60

Бренд: Texas Instruments Страницы: 20

Бренд: Aeroflex Страницы: 32

Бренд: Gigabyte Страницы: 2

Бренд: THORLABS Страницы: 22

Бренд: IEI Technology Страницы: 163

Бренд: JETWAY Страницы: 47

Бренд: Atmel Страницы: 74

Бренд: Foxconn Страницы: 106

Бренд: TYAN Страницы: 54

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды