Honda BF200D Скачать руководство пользователя страница 1

Страница: 1 / 152

Thank you for purchasing a Honda

Outboard Motor.

This manual covers operation and

maintenance of the Honda BF200D/

BF225D/BF250D Outboard Motor.

All information in this publication is

based on the latest product

information available at the time of

approval for printing.

Honda Motor Co., Ltd. reserves the

right to make changes at any time

without notice and without incurring

any obligation.

No part of this publication may be

reproduced without written

permission.

This manual should be considered a

permanent part of the Outboard

Motor and should remain with it if it

is resold.

Throughout this manual, you will see

safety messages proceeded by the

following words and symbols. Here’s

what they mean:

Indicates that equipment or

property damage could result if

instructions are not followed.

Gives helpful information.

If a problem should arise, or if you

have any questions about the

Outboard Motor, consult an

authorized Honda Outboard Motor

dealer.

Honda Motor Co., Ltd. 2018, All

Rights Reserved

DANGER

Indicates serious injury or death

WILL result if instructions are

not followed.

WARNING

Indicates a strong possibility that

serious personal injury or death

may result if instructions are not

followed.

CAUTION

Indicates a possibility that

personal injury or equipment

damage could result if

instructions are not followed.

WARNING

Honda Outboard Motors are

designed to give safe and

dependable service if operated

according to instructions. Read

and understand the Owner’s

Manual before operating the

Outboard Motor. Failure to do so

could result in personal injury or

equipment damage.

42ZVL600.book 1 ページ２０１８年７月１９日　木曜日　午前９時６分

Содержание BF200D

























































































































































Результаты поиска

Содержание BF200D

Отзывы:

Похожие инструкции для BF200D

Бренды по названию

Популярные бренды

Honda BF200D, Руководство пользователя

Результаты поиска

Содержание BF200D

Отзывы:

Похожие инструкции для BF200D

Бренды по названию

Популярные бренды