manualshive.com logo in svg

Honda BF200D, Руководство пользователя, Страница: 74 / 152

Поделиться
Скачать
Honda BF200D Скачать руководство пользователя страница 74

74

STARTING THE ENGINE

4. After starting, check whether the 

cooling water is flowing out of the 

cooling water check hole. Amount 

of water flowing out of the check 

hole might vary due to the 

thermostat operation, but this is 

normal.

If water does not flow out, or if 

steam comes out, stop the engine. 

Check to see if the screen in the 

cooling water intake port is 

obstructed and remove foreign 

materials if necessary. Check the 

cooling water check hole for 

clogging. If water still does not flow 

out, have your outboard motor 

checked by an authorized Honda 

outboard motor dealer. Do not 

operate the engine until the 

problem has been corrected.

5. Check to see if the oil pressure 

indicator turns ON.

If it does not turn on, stop the engine 

and perform the following 

inspections.

1) Check the oil level (see page 59).

2) If the oil level is normal and the oil 

pressure indicator does not turn 

ON, consult with an authorized 

Honda outboard motor dealer.

6. Warm up the engine as follows: 

Above 5°C (41°F) – run the engine 

for 2 or 3 minutes.

Below 5°C (41°F) – run the engine  
for at least 5 minutes at 2,000 min

-1

 

(rpm).

Failure to completely warm up the 

engine will result in poor engine 

performance.

COOLING WATER CHECK HOLE

COOLING WATER INTAKE PORT 

(each side)

OIL PRESSURE 

INDICATOR LIGHT

NORMAL: ON  

ABNORMAL: OFF

NORMAL: OFF

ABNORMAL: ON

42ZVL600.book  74 ページ  ２０１８年７月１９日　木曜日　午前９時６分

Содержание BF200D

























































































































































Отзывы:

Нет отзывов