Honda BF200D Скачать руководство пользователя страница 87

Страница: 87 / 152

OPERATION

1. Press on the DN (down) of the

power trim/tilt switch and trim the

outboard motor at the lowermost

position.

D2 type:

When the two or more outboard

motors are mounted:

1)Press on the DN (down) of the

power trim/tilt switch on the remote

control lever and trim the outboard

motors at the lowermost position.

2)With the outboard motors trimmed

at the lowermost position, adjust the

trim angle of the each outboard

motor using the switch on the panel.

R3 type:

When the two outboard motors are

mounted:

1) Press on the DN (down) of the

power trim/tilt switch on the

remote control lever and trim the

outboard motors at the lowermost

position.

2) With the outboard motors trimmed

at the lowermost position, adjust

the trim angle of the right and left

outboard motors using the switch

on the remote control lever

simultaneously.

42ZVL600.book 87 ページ２０１８年７月１９日　木曜日　午前９時６分

Содержание BF200D

























































































































































Результаты поиска

Содержание BF200D

Отзывы:

Похожие инструкции для BF200D

Бренды по названию

Популярные бренды

Honda BF200D, Руководство пользователя

Результаты поиска

Содержание BF200D

Отзывы:

Похожие инструкции для BF200D

Бренды по названию

Популярные бренды