Honda BF200D Скачать руководство пользователя страница 97

Страница: 97 / 152

OPERATION

Tilt up the outboard motor using the

tilt lock lever when mooring the boat.

Shift the control lever into the

NEUTRAL position and stop the

engine before tilting up the outboard

motor.

Before tilting up, leave the outboard

motor in the running position for one

minute after stopping the engine to

drain the water from inside the

engine.

Stop the engine and disconnect the

fuel line from the outboard motor

before tilting the outboard motor.

1. Raise the outboard motor as full as

it goes using the power trim/tilt

switch.

2. Move the tilt lock lever to the

LOCK position and lower the

outboard motor until the lock lever

contacts the stern bracket.

3. Press the DN (down) of the power

trim/tilt switch and fully shorten

the trim rods.

4. To tilt down, raise the outboard

motor slightly, move the tilt lock

lever to the FREE position.

After tilting down the outboard

motors, adjust the trim angle of the

right and left outboard motors.

POWER TRIM/TILT SWITCH

(LEFT)

(RIGHT)

TRIM RODS

TILT LOCK LEVER

STERN BRACKET

FREE

LOCK

Moorage

42ZVL600.book 97 ページ２０１８年７月１９日　木曜日　午前９時６分

Содержание BF200D

























































































































































Результаты поиска

Содержание BF200D

Отзывы:

Похожие инструкции для BF200D

Бренды по названию

Популярные бренды

Honda BF200D, Руководство пользователя

Результаты поиска

Содержание BF200D

Отзывы:

Похожие инструкции для BF200D

Бренды по названию

Популярные бренды