Honda BF200D Скачать руководство пользователя страница 72

Страница: 72 / 152

STARTING THE ENGINE

(R1 type)

To prevent damage to the outboard

from overheating, never run the

engine with the propeller out of

water.

1. Insert the emergency stop switch

clip at one end of the emergency

stop switch lanyard into the

emergency stop switch. Attach the

other end of the lanyard securely to

the operator.

The engine does not start unless the

emergency stop switch clip is set on

the emergency stop switch.

A spare emergency stop switch clip

can be stored in the tool bag (see page

115).

WARNING

Exhaust contains poisonous

carbon monoxide which can

cause unconsciousness and may

lead to death. Never run the

outboard motor in a boat house or

other confined area.

EMERGENCY STOP SWITCH

STOP

EMERGENCY STOP

SWITCH CLIP

EMERGENCY STOP

SWITCH LANYARD

WARNING

If the operator does not attach the

emergency stop switch lanyard,

and is thrown from the seat or out

of the boat, the out-of-control

boat can seriously injure the

operator, passengers, or

bystanders. Always properly

attach the lanyard before starting

the engine.

EMERGENCY STOP

SWITCH CLIP

42ZVL600.book 72 ページ２０１８年７月１９日　木曜日　午前９時６分

Содержание BF200D

























































































































































Результаты поиска

Содержание BF200D

Отзывы:

Honda BF200D, Руководство пользователя, Страница: 72 / 152

Результаты поиска

Содержание BF200D

Отзывы: