Yamaha F30 Скачать руководство пользователя | Manualshive

Страница: 57 / 120

background image

Operation

51

connector is securely screwed on to the fit-
ting on the bottom cowling.

NOTICE:

If the

garden hose connector is not properly
connected, cooling water can leak out
and the engine can overheat during oper-
ation.

[ECM01802]

EMU36956

Install top cowling

1. Be sure that the cowling lock lever is re-

leased.

2. Be sure that the rubber seal is seated all

the way around the top cowling.

3. Place the top cowling on the bottom

cowling.

4. Check to be sure the rubber seal is seat-

ed correctly between the top cowling
and the bottom cowling.

5. Move the cowling lock lever to lock the

top cowling as shown.

NOTICE:

If the

top cowling is not installed correctly,
water spray under the top cowling
can damage the engine, or the top
cowling can blow off at high speeds.

[ECM01992]

After installing, check the fitting of the top
cowling by pushing it with both hands. If the
top cowling is loose, have it repaired by your
Yamaha dealer.

EMU38911

Checking power trim and tilt system

WARNING

EWM01971



Never get under the lower unit while it
is tilted, even when the tilt support
knob is locked. Severe injury could oc-
cur if the outboard motor accidentally
falls.



Body parts can be crushed between the
motor and the clamp bracket when the
motor is trimmed or tilted.



Be sure no one is near the outboard
motor before performing this check.

1. Check the power trim and tilt unit for any

sign of oil leaks.

2. Operate each of the power trim and tilt

1. Fitting
2. Flushing device

2

1

ZMU06401

ZMU06110

6BG-9-3F-E0.book 51 ページ２０１８年１１月１日　木曜日　午後５時１分

©2020

Yamaha

Motor

Corporation

«
...
55
56
57
58
59
...
»

Содержание F30

























































































































Отзывы:

Нет отзывов

Похожие инструкции для F30

Бренд: Biostar Страницы: 47

Бренд: Texas Instruments Страницы: 22

Бренд: AOpen Страницы: 96

Бренд: Intel Страницы: 78

Бренд: Quantum Страницы: 69

945GC MICRO 775

Бренд: Biostar Страницы: 49

Бренд: Texas Instruments Страницы: 21

Бренд: MSI Страницы: 92

Бренд: MATSONIC Страницы: 77

Бренд: Gigabyte Страницы: 104

Бренд: ASROCK Страницы: 200

Бренд: Watersnake Страницы: 20

Бренд: Gigabyte Страницы: 34

Бренд: ECS Страницы: 71

IRIS-W10 Series

Бренд: Ublox Страницы: 43

PHANTOM GAMING X670E PG Lightning

Бренд: ASROCK Страницы: 66

Бренд: DFI Страницы: 76

Бренд: Asus Страницы: 68

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды