Yamaha F30 Скачать руководство пользователя

Страница: 116 / 120

INDEX

110

Gasoline............................................ 1, 19
Gasoline Additives ................................ 20
Gasoline exposure and spills.................. 2
Gear oil, changing................................. 93
Gear shift lever ..................................... 28
Greasing ............................................... 85

Hot parts ................................................. 1
Hour meter............................................ 37

Identification numbers record ............... 10
Idle speed, inspecting ........................... 87
Impact damage ................................... 100
Installation requirements....................... 16
Instruments and indicators.................... 36

Key number .......................................... 10

Laws and regulations.............................. 4
Low battery voltage-alert indicator........ 40
Low oil pressure alert............................ 44
Low oil pressure-alert indicator....... 36, 37
Lubrication ............................................ 78

Main switch ........................................... 31
Maintenance chart 1 ............................. 82
Maintenance chart 2 ............................. 84
Maintenance interval guidelines ........... 80
Modifications........................................... 2
Mounting height .................................... 46
Mounting outboard motor...................... 16
Mounting the outboard motor................ 46
Muddy or acidic water........................... 21

Neutral interlock trigger......................... 28
Neutral throttle lever ............................. 28

Operating engine .................................. 55
Outboard motor disposal

requirements....................................... 22

Outboard motor (painted surface),

checking ............................................. 80

Outboard motor safety ............................ 1
Outboard motor serial number.............. 10
Overheat alert ....................................... 44
Overheat-alert indicator .................. 36, 38
Overloading ............................................ 2

Passengers............................................. 2
Passenger training.................................. 4
People in the water ................................. 2
Periodic maintenance ........................... 80
Personal flotation devices (PFDs) .......... 2
Power trim and tilt ................................... 1
Power trim and tilt switch (bottom

cowling) .............................................. 32

Power trim and tilt switch (remote

control or tiller handle) ........................ 32

Power trim and tilt system, checking..... 51
Power trim and tilt will not operate...... 101
Propeller ................................................. 1
Propeller, checking ............................... 91
Propeller, installing ............................... 92
Propeller, removing............................... 92
Propeller selection ................................ 17

Read manuals and labels ..................... 12
Remote control box............................... 27
Remote control lever............................. 27
Remote control requirements ............... 16
Replacement parts................................ 80
Replacing the engine oil filter................ 90
Rotating parts ......................................... 1
Rules when encountering vessels .......... 6

Sending fuel (portable tank).................. 56
Shallow water ....................................... 72

6BG-9-3F-E0.book 110 ページ２０１８年１１月１日　木曜日　午後５時１分

Yamaha

Motor

Corporation

Содержание F30

























































































































Результаты поиска

Содержание F30

Отзывы:

Похожие инструкции для F30

Бренды по названию

Популярные бренды

Yamaha F30, Руководство пользователя

Результаты поиска

Содержание F30

Отзывы:

Похожие инструкции для F30

Бренды по названию

Популярные бренды