manualshive.com logo in svg

Yamaha F30, Руководство пользователя

Поделиться
Скачать
Yamaha F30 Скачать руководство пользователя страница 93

Maintenance

87

allow external sparks, which could
lead to explosion or fire.

 [EWM00562]

3. Be sure to use the specified spark plug,

otherwise the engine may not operate
properly. Before fitting the spark plug,
measure the electrode gap with a wire
thickness gauge; replace it if out of spec-
ification.

4. When fitting the plug, wipe off any dirt

from the threads, and then screw it in to
the correct torque.

TIP:

If a torque-wrench is not available when you
are reinstalling a spark plug, a good estimate
of the correct torque is 1/12 turn past finger-
tight. When you are installing a new spark
plug, a good estimate of the correct torque is
1/2 turn past finger-tight.

EMU29045

Inspecting idle speed

WARNING

EWM00452

Do not touch or remove electrical parts
when starting or during operation.

Keep hands, hair, and clothes away
from the flywheel and other rotating
parts while the engine is running.

NOTICE

ECM00491

This procedure must be performed while
the outboard motor is in the water. A
flushing attachment or test tank can be
used.

If the boat is not equipped with a tachometer
for the outboard motor, use a diagnostic ta-
chometer for this procedure. Results may
vary depending on whether testing is con-
ducted with the flushing attachment, in a test
tank, or with the outboard motor in the water.
1. Start the engine and allow it to warm up

fully in neutral until it is running smooth-
ly.

2. Once the engine has warmed up, verify

whether the idle speed is set to specifi-
cation. For idle speed specifications, see
page 15. If you have difficulty verifying
the idle speed, or the idle speed requires
adjustment, consult a Yamaha dealer or
other qualified mechanic.

EMU38808

Changing engine oil

WARNING

EWM00761

Avoid draining the engine oil immedi-
ately after stopping the engine. The oil
is hot and should be handled with care
to avoid burns.

Be sure the outboard motor is securely
fastened to the transom or a stable

Standard spark plug:

DPR6EB-9

1. Spark plug gap
2. Spark plug part number
3. Spark plug I.D. mark (NGK)

Spark plug gap:

0.8–0.9 mm (0.031–0.035 in)

Spark plug torque:

17 N·m (1.7 kgf·m, 13 lb·ft)

6BG-9-3F-E0.book  87 ページ  ２０１８年１１月１日　木曜日　午後５時１分

©2020 

Yamaha 

Motor 

Corporation

Содержание F30

























































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды