Yamaha F30 страница 107 Скачать руководство пользователя

Страница: 107 / 120

Trouble Recovery

101

EMU29513

Power trim and tilt will not operate

If the engine cannot be tilted up or down with
the power trim and tilt because of a dis-
charged battery or a failure with the power

trim and tilt unit , the engine can be tilted
manually.
1. Loosen the manual valve screw by turn-

ing it clockwise until it stops.

2. Put the engine in the desired position,

then tighten the manual valve screw by
turning it counterclockwise.

EMU37573

Water separator-alert indicator blinks
while cruising

WARNING

EWM01501

Gasoline is highly flammable, and its va-
pors are flammable and explosive.



Do not perform this procedure on a hot
or running engine. Allow the engine to
cool.



There will be fuel in the fuel filter. Keep
away from sparks, cigarettes, flames or
other sources of ignition.



This procedure will allow some fuel to
spill. Catch fuel in a rag. Wipe up any
spilled fuel immediately.



The fuel filter must be reassembled
carefully with the O-ring, filter cup, and
hoses in place. Improper assembly or
replacement could result in a fuel leak,
which could result in a fire or explosion
hazard.

1. Fuse (20 A



2, 30 A)

2. Spare fuse (20 A



2, 30 A)

3. Fuse puller

1. Fuse puller

ZMU06422

ZMU04337

1. Manual valve screw

ZMU04095

6BG-9-3F-E0.book 101 ページ２０１８年１１月１日　木曜日　午後５時１分

Yamaha

Motor

Corporation

Содержание F30

























































































































Результаты поиска

Содержание F30

Отзывы:

Похожие инструкции для F30

Бренды по названию

Популярные бренды

Yamaha F30, Руководство пользователя

Результаты поиска

Содержание F30

Отзывы:

Похожие инструкции для F30

Бренды по названию

Популярные бренды