Yamaha F30 Скачать руководство пользователя | Manualshive

Страница: 84 / 120

background image

Maintenance

78

5. Cooling system flushing is essential to

prevent the cooling system from clog-
ging up with salt, sand, or dirt. In addi-
tion, fogging/lubricating of the engine is
mandatory to prevent excessive engine
damage due to rust. Perform the flush-
ing and fogging at the same time.

WARNING! Do not touch or remove
electrical parts when starting or dur-
ing operation. Keep hands, hair, and
clothes away from the flywheel and
other rotating parts while the engine
is running.

[EWM00092]

TIP:



When using the flushing attachment, main-
tain adequate water pressure and a steady
water flow.



If the overheat alert device is activated,
turn the engine off, and consult your
Yamaha dealer.

6. Run the engine at a fast idle for a few

minutes in neutral position while supply-
ing fresh water.

7. Just prior to turning off the engine, quick-

ly spray “Yamaha Stor-Rite Engine
Fogging Oil” alternately into the intake
silencer or the fogging hole of the silenc-
er cover, if equipped. When properly
done, the engine will smoke excessively

and almost stall.

8. Remove the flushing attachment and

wipe off any excess water.

9. Install the top cowling and propeller.
10. Drain the cooling water completely out of

the motor. Clean the body thoroughly.

TIP:

A flushing attachment is available from your
Yamaha dealer.

EMU41072

Lubrication

1. Change the gear oil. For instructions,

see page 93. Check the gear oil for the
presence of water that indicates a leaky
seal. Seal replacement should be per-
formed by an authorized Yamaha dealer
prior to use.

2. Lubricate all grease fittings. For further

details, see page 85.

TIP:

For long-term storage, fogging the engine
with fogging oil is recommended. Contact
your Yamaha dealer for information about
fogging oil and procedures for your outboard
motor.

EMU30269

Cleaning and anticorrosion
measures

1. Wash down the exterior of the outboard

motor with fresh water and dry off com-
pletely.

NOTICE:

Do not spray water

into the air intake.

[ECM01841]

For further

information, see page 79.

2. Spray the outboard motor exterior with

“Yamaha Silicone Protectant”.

NOTICE:

Do not spray when the engine is run-
ning. Also, do not spray near the si-
lencer or into the engine. Otherwise
the engine could be damaged.

[ECM01403]

3. Wax the cowling with a non-abrasive

wax such as “Yamalube Professional

1. Flushing attachment

6BG-9-3F-E0.book 78 ページ２０１８年１１月１日　木曜日　午後５時１分

©2020

Yamaha

Motor

Corporation

«
...
82
83
84
85
86
...
»

Содержание F30

























































































































Отзывы:

Нет отзывов

Похожие инструкции для F30

Бренд: Intel Страницы: 78

Бренд: DFI Страницы: 104

Бренд: Oki Страницы: 24

Бренд: ASROCK Страницы: 2

Бренд: H-Tec Страницы: 28

Бренд: Fastfame Страницы: 41

i.MX 8M Mini SODIMM SOM

Бренд: iWave Страницы: 16

Бренд: Gigabyte Страницы: 96

Бренд: FIC Страницы: 68

D850MV - Desktop Board Motherboard

Бренд: Intel Страницы: 25

Бренд: Outboards Group Страницы: 44

Бренд: AZZA Страницы: 43

Бренд: Analog Devices Страницы: 4

cPCI-6620 Series

Бренд: ADLINK Technology Страницы: 80

Бренд: Supermicro Страницы: 1

Бренд: Micrel Страницы: 6

Бренд: Micrel Страницы: 10

Бренд: Micrel Страницы: 25

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды