manualshive.com logo in svg

Yamaha F30, Руководство пользователя

Поделиться
Скачать
Yamaha F30 Скачать руководство пользователя страница 78

Operation

72

3. Push the power trim and tilt switch “

”

(down) to lower the outboard motor to
the desired position.

EMU28063

Shallow water 

EMU28082

Hydro tilt models

The outboard motor can be tilted up partially
to allow operation in shallow water.

WARNING

EWM00272

Run the boat at the lowest possible
speed when using the shallow water
cruising system.

Use extra care when operating in re-
verse. Too much reverse thrust can
cause the outboard motor to lift out of
the water, increasing the chance of ac-
cident and personal injury.

NOTICE

ECM00261

Do not tilt the outboard motor up so that
the cooling water inlet on the lower unit is
above the surface of the water when set-
ting up for and cruising in shallow water.
Otherwise severe damage from overheat-
ing can result.

EMU32841

Procedure for hydro tilt models

1. Place the gear shift lever in neutral.

DN

ZMU01936

DN

ZMU06410

ZMU03646

6BG-9-3F-E0.book  72 ページ  ２０１８年１１月１日　木曜日　午後５時１分

©2020 

Yamaha 

Motor 

Corporation

Содержание F30

























































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды