manualshive.com logo in svg

Yamaha F30, Руководство пользователя

Поделиться
Скачать
Yamaha F30 Скачать руководство пользователя страница 72

Operation

66

2. After stopping the engine, disconnect

the fuel hose from the fuel joint on the
outboard motor.

3. Disconnect the fuel hose from the fuel

joint on the fuel tank.

4. Tighten the air vent screw by turning it

clockwise.

5. Remove the key if the boat will be left un-

attended.

TIP:

The engine can also be stopped by pulling
the cord and removing the clip from the en-
gine shut-off switch, then turning the main
switch to “

” (off).

EMU27865

Trimming outboard motor

WARNING

EWM00741

Excessive trim for the operating condi-
tions (either trim up or trim down) can
cause boat instability and can make
steering the boat more difficult. This in-
creases the possibility of an accident. If
the boat begins to feel unstable or is hard
to steer, slow down and/or readjust the
trim angle.

The trim angle of the outboard motor helps
determine the position of the bow of the boat
in the water. Correct trim angle will help im-
prove performance and fuel economy while
reducing strain on the engine. Correct trim
angle depends upon the combination of
boat, engine, and propeller. Correct trim is
also affected by variables such as the load in

1. Fuel joint
2. Fuel hose

1. Fuel joint
2. Fuel hose

1

2

ZMU07586

ZMU07443

2

1

1. Air vent screw

1

ZMU07444

6BG-9-3F-E0.book  66 ページ  ２０１８年１１月１日　木曜日　午後５時１分

©2020 

Yamaha 

Motor 

Corporation

Содержание F30

























































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды