Yamaha F30 Скачать руководство пользователя

Страница: 44 / 120

Instruments and indicators

EMU26584

Overheat-alert indicator

If the engine temperature rises too high, the
alert indicator will start to blink. For further in-
formation on reading the indicator, see page
44.

NOTICE

ECM00053

Do not continue to run the engine if the
overheat-alert indicator is on. Serious en-
gine damage will occur.

EMU26603

Digital speedometer

This gauge shows the boat speed and other
information.

All segments of the display will light momen-
tarily after the main switch is turned on and
will return to normal thereafter.

EMU36062

Speedometer

The speedometer displays km/h, mph, or
knots, according to operator preference. Se-
lect the desired units of measurement by set-
ting the selector switch on the back of the
gauge. See the illustration for settings.

EMU26714

Fuel gauge

Eight segments indicate the fuel level. When

1. Low oil pressure-alert indicator

1. Overheat-alert indicator

ZMU01736

ZMU01737

1. Speedometer
2. Fuel gauge
3. Trip meter/clock/voltmeter
4. Alert indicator(s)

1. Cap
2. Selector switch (for speed unit)
3. Selector switch (for fuel sensor)

km/h
(km)

mph
(mile)

knots
(mile)

1234

ZMU07001

6BG-9-3F-E0.book 38 ページ２０１８年１１月１日　木曜日　午後５時１分

Yamaha

Motor

Corporation

Содержание F30

























































































































Результаты поиска

Содержание F30

Отзывы:

Похожие инструкции для F30

Бренды по названию

Популярные бренды

Yamaha F30, Руководство пользователя

Результаты поиска

Содержание F30

Отзывы:

Похожие инструкции для F30

Бренды по названию

Популярные бренды