Xerox Versant 3100 Press Скачать руководство пользователя страница 124 | Manualshive

Страница: 124 / 170

background image

Reducing Toner Consumption

Problem

In order to maintain image quality (IQ), the press will enter “Adjust Image Quality” mode. In
this mode, toner is consumed in the form of toner bands and process control patches being laid
down. Frequency of the “Adjust Image Quality” is dependent on many factors including area
coverage. While printing jobs of low area coverage/low image density, the frequency of “Adjust
Image Quality” may be greater.

Suggested Solution

Three NVM values can be adjusted to reduce toner consumption based on user requirements.
Refer to the following table. From the first column of the table, select the solution which best
fits user requirements, and then change the NVM values as shown for each of the three NVM
settings.

Important

To select the outcome appropriate for your environment, contact the system administrator.

NVM 762-108

NVM 752-175

NVM 762-085

User Requirement

Set NVM to 3

Set NVM to 1 (On)

Set NVM to 1 (On)

1. Image Quality (IQ) Priority
These are the press default set-
tings which provide optimum IQ
output, but increase toner con-
sumption and may reduce pro-
ductivity.

Set NVM to 1

Set NVM to 0 (Off)

Set NVM to 1 (On)

2. Middle Setting

Note

This is the recommended setting.

These settings configure the
press for less toner usage if im-
age quality is not the highest
priority. IQ may be slightly re-
duced.

No change required

No change re-
quired

Set NVM to 0 (Off)

3. Lower Toner Consumption Pri-
ority
These settings decrease toner
usage and increase productivity,
but may result in degraded IQ.

Xerox

®

Versant

®

3100 Press

7-6

User Guide

Troubleshooting

«
...
122
123
124
125
126
...
»

Содержание Versant 3100 Press











































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Versant 3100 Press

Бренд: IBM Страницы: 112

Бренд: Labelmate Страницы: 2

Бренд: Panasonic Страницы: 166

WORKCENTRE 5050

Бренд: Xerox Страницы: 186

7500DX - Phaser Color LED Printer

Бренд: Xerox Страницы: 5

Saddle Finisher-AF2

Бренд: Canon Страницы: 244

Aficio MP C6503SP

Бренд: Ricoh Страницы: 264

Бренд: SEH Страницы: 50

WorkCentre 7655

Бренд: Xerox Страницы: 19

Бренд: Rokit Страницы: 16

Бренд: FOREVER Страницы: 2

B-470-QQ Series

Бренд: TEC Страницы: 32

VarioPrint 4110

Бренд: Oce Страницы: 216

Бренд: SEWOO Страницы: 24

Бренд: Kyocera Страницы: 72

imageRUNNER ADVANCE DX C7700 Series

Бренд: Canon Страницы: 127

Бренд: Canon Страницы: 146

Бренд: Epson Страницы: 277

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды