Xerox Versant 3100 Press Скачать руководство пользователя страница 96

Страница: 96 / 170

Replacing a Dry Ink / Toner Cartridge

Note

The dry ink / toner cartridge can be replaced while a job is printing.

1. Open the dry ink / toner cover, located just above the press front door / cover.

2. Lay paper on the floor before removing the cartridge. This will allow any excess dry

ink / toner to fall on the paper.

3. Slowly remove the dry ink / toner cartridge by placing fingers under the end of the

cartridge and gently pulling it straight out. While pulling out, hold the bottom of the
cartridge with your other hand to give it support.

Ensure that you are removing the same cartridge that matches the color as indicated
in the message.

4. Dispose of or recycle the cartridge per your local authorities and regulations.

In the United States, also refer to the Electronic Industries Alliance website:

www.eiae.org

. For more information about Xerox environmental programs, go to

www.xerox.com/environment

5. Remove the new dry ink / toner cartridge from its packaging.
6. Prepare the cartridge for installation:

Xerox

Versant

3100 Press

6-20

User Guide

Maintenance

Содержание Versant 3100 Press











































































































































































Результаты поиска

Содержание Versant 3100 Press

Отзывы:

Похожие инструкции для Versant 3100 Press

Бренды по названию

Популярные бренды

Xerox Versant 3100 Press, Руководство пользователя

Результаты поиска

Содержание Versant 3100 Press

Отзывы:

Похожие инструкции для Versant 3100 Press

Бренды по названию

Популярные бренды