Xerox Versant 3100 Press Скачать руководство пользователя страница 20 | Manualshive

Страница: 20 / 170

background image

Full System Configuration

Note

Full system configurations will vary depending on which optional devices are attached
to the press. For detailed information on optional devices, refer to the Optional Devices
Guide for Xerox

®

Versant

®

3100 Press.

The following illustration shows an example of a full system configuration with optional
devices attached; this is only one example.

6.

1.

High Capacity Stacker*

Dual Advanced High Capacity Feeder
(Trays 8 and 9)*

7.

Two-sided Trimmer*

2.

Advanced High Capacity Feeder (Trays
6 and 7)

8.

C/Z Folder*

9.

Production Ready (PR) Booklet Maker
Finisher*

3.

Color Press

4.

Interface Decurler Module (IDM)*

10. SquareFold

®

Trimmer*

5.

Inserter*

* Numbers 1 and 4-10 indicate optional devices.

Power On / Off

Power Switches

There are three power switches involved with the press:

• Circuit Breaker Switch
• Main Power Switch
• Power On / Off Button

Important

Always use the Power On / Off button first, and then power off the Main Power Switch.

Xerox

®

Versant

®

3100 Press

2-8

User Guide

Getting Started

«
...
18
19
20
21
22
...
»

Содержание Versant 3100 Press











































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Versant 3100 Press

CLP-680ND: CLP-775ND

Бренд: Samsung Страницы: 2

Бренд: QMS Страницы: 2

Бренд: Qilive Страницы: 398

Magicolor 2 plus

Бренд: QMS Страницы: 90

Magicolor 2 Desklaser

Бренд: QMS Страницы: 4

Бренд: QMS Страницы: 8

Бренд: QMS Страницы: 94

Бренд: QMS Страницы: 6

imagePROGRAF GP-540

Бренд: Canon Страницы: 82

imageRUNNER ADVANCE DX 6870i

Бренд: Canon Страницы: 115

imagerunner advance C5550i

Бренд: Canon Страницы: 1556

Бренд: Konica Minolta Страницы: 61

Бренд: Star Страницы: 24

N2125N - DocuPrint B/W Laser Printer

Бренд: Xerox Страницы: 335

Бренд: Oki Страницы: 182

Бренд: VASTEX Страницы: 8

Бренд: Brady Страницы: 48

Бренд: Ricoh Страницы: 284

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды