Woodward IKD 1 Скачать руководство пользователя страница 32

Страница: 32 / 41

Manual 37135C

IKD 1 - Digital I/O Expansion Board

Page 32/41

Appendix C.

Technical Data

Ambient variables ----------------------------------------------------------------------------------------------

Power supply (V

aux

) ---------------------------------------------------- 12/24 Vdc (6.0 to 36.0 Vdc)

Intrinsic consumption ------------------------------------------------------------------------- max. 3 W

Ambient temperature for storage ------------- -40 to 85 °C / -40 to 185 °F (P/N: 8440-2028)

Ambient temperature for storage ------------- -30 to 80 °C / -22 to 176 °F (P/N: 8440-1041)

Ambient temperature for operation ----------------------------------- -20 to 70 °C / -4 to 158 °F

Ambient humidity -------------------------------------------------------------- 95 %, not condensing

Discrete inputs ------------------------------------------------------------------------ galvanically isolated

Input range (V

Cont., dig.input

) -------------------------------- Rated voltage 12/24 Vdc (6 to 32 Vdc)

Input resistance ------------------------------------------------------------------------- approx. 6.8 k

Ω

Relay outputs ---------------------------------------------------------------------------------- potential free

Contact material --------------------------------------------------------------------------------- AgCdO

General purpose (GP) (V

Cont, relay output

)

AC ------------------------------------ 2.00 Aac@250 Vac

DC -------------------------------------- 2.00 Adc@24 Vdc

------------------------------------ 0.36 Adc@125 Vdc

------------------------------------ 0.18 Adc@250 Vdc

Pilot duty (PD) (V

Cont, relay output

)

AC ------------------------------------------------------ B300

DC -------------------------------------- 1.00 Adc@24 Vdc

------------------------------------ 0.22 Adc@125 Vdc

------------------------------------ 0.10 Adc@250 Vdc

Interface, Service interface -----------------------------------------------------------------------------------

Version -------------------------------------------------------------------------------------------- RS-232

Signal level -------------------------------------------------------------------------------------------- 5 V

---------------------------------- Level conversion and insulation by using DPC (P/N 5417-557)

Interface, CAN ----------------------------------------------------------------------- galvanically isolated

Insulation voltage (continuously) ------------------------------------------------------------ 100 Vdc

Insulation test voltage (≤ 5 s) --------------------------------------------------------------- 1,000 Vac

Version ------------------------------------------------------------------------------------------ CAN-Bus

Internal line termination ------------------------------------------------------------------ not available

Housing ----------------------------------------------------------------------------------------------------------

Extrusion profile

for fastening onto a DIN rail/C profile ------------------------------- Um 122

Dimensions ------------------------------------------------------------------------ 168 × 128 × 51 mm

Vibration absorber

------------------------------------------------------------------------------ M4×6

Dimensions ------------------------------------------------------------------------ 152 × 122 × 52 mm

Wiring ------------------------------------------------------------------Screw-plug terminals 2.5 mm²

------------------------------------------------------------------ Recommended locked torque 0.5 Nm

-------------------------------------------------------------------------- use 60/75 °C copper wire only

--------------------------------------------------------------------- use class 1 wire only or equivalent

Weight-------------------------------------------------------------------------------------- approx. 360 g

Protection --------------------------------------------------------------------------------------------------------

Protection type -------------------------------------------------------------------------------------- IP 00

EMC test (CE) -------------------------------------- tested according to applicable EN guidelines

Type approval ............... UL/cUL, Ordinary Locations, File No.: 231544 (P/N: 8440-2028)

Содержание IKD 1










































Результаты поиска

Содержание IKD 1

Отзывы:

Woodward IKD 1, Руководство пользователя, Страница: 32 / 41

Результаты поиска

Содержание IKD 1

Отзывы: