Woodward IKD 1 Скачать руководство пользователя страница 19 | Manualshive

Страница: 19 / 41

Woodward IKD 1 Скачать руководство пользователя страница 19

Manual 37135C

IKD 1 - Digital I/O Expansion Board

© Woodward

Page 19/41

Chapter 5.

LEDs And Interfaces

LEDs

≡≡≡≡≡≡≡≡≡≡≡≡≡≡≡≡≡≡≡≡≡≡≡≡≡

The LEDs on the PCB are used to display the status of the unit.

LED A

"Readiness for operation"

Color: GREEN

This LED indicates that power supply has been applied.

LED B

"CAN bus"

Color: YELLOW

Is the CAN bus active this LED is flashing.

LED C

"Alarm"

Color: RED

This LED indicates an alarm. Is a discrete input triggered and is at least alarm class 1

configured to the input the LED is shining.

LED input 1 to 8

Color: YELLOW

This LED indicates the

physical status

of the inputs. Is a input set to a high level this

LED is shining.

Interfaces

≡≡≡≡≡≡≡≡≡≡≡≡≡≡≡≡≡≡≡≡≡≡≡≡≡

The IKD 1 is equipped with two interfaces working with the following baud rates:

•

Direct configuration

1,200 Baud (8 Bit, no parity, 1 Stop bit) and

•

CAN bus (CiA)

125, 250 or 500 kBaud configurable using the serial interface.

Direct Configuration (DPC)

≡≡≡≡≡≡≡≡≡≡≡≡≡≡≡≡≡≡≡≡≡≡≡≡≡

Using the configuration interface the unit can be configured directly. Therefore a direct configuration cable DPC

is necessary that is connected on one side with the PC/laptop and on the other side at the unit.

For the direct configuration a file is necessary that can be opened using the PC program LeoPC1 (file name: xxxx-

xxxx-yyy-zz.asm, whereas 'xxxx-xxxx' is the product number, 'yyy' the revision number and 'zz' the language [US

= English, DE = German]). The parameters described in chapter "Configuration" beginning page 20 could be

modified with this file.

«
...
17
18
19
20
21
...
»

Содержание IKD 1










































Отзывы:

Нет отзывов