Woodward IKD 1 Скачать руководство пользователя страница 20 | Manualshive

Страница: 20 / 41

Woodward IKD 1 Скачать руководство пользователя страница 20

Manual 37135C

IKD 1 - Digital I/O Expansion Board

Page 20/41

© Woodward

Chapter 6.

Configuration

Configuration can be carried out using a PC and the PC program LeoPC1^1 via the serial interface. Additionally

configuration can be carried out via the CAN bus. The following baud rates apply:

•

Configuration via direct configuration = 1,200 Baud and

•

CAN bus configuration: The baud rate corresponds to the baud rate for transmitting and receiving messages.

It can be configured using the direct configuration (125, 250, 500 kBaud according CiA).

CAUTION

Do not change parameters during operation.

The parameters can be changed using the PC program LeoPC1 (see separate manual).

NOTE

Please note the list of parameters at the end of this manual.

Basic Data

≡≡≡≡≡≡≡≡≡≡≡≡≡≡≡≡≡≡≡≡≡≡≡≡≡

Software version

Software version

Version number of the software.

Software number

Software number for identification

Unique identification number.

«
...
18
19
20
21
22
...
»

Содержание IKD 1










































Отзывы:

Нет отзывов