manualshive.com logo in svg

Woodward IKD 1, Руководство пользователя, Страница: 14 / 41

Поделиться
Скачать
Woodward IKD 1 Скачать руководство пользователя страница 14

Manual 37135C 

IKD 1 - Digital I/O Expansion Board 

 

 

 

 

Page 14/41 

© Woodward 

Main Functions 

≡≡≡≡≡≡≡≡≡≡≡≡≡≡≡≡≡≡≡≡≡≡≡≡≡ 

Coupling to a Higher Level Control Unit (e.g. GCP) 

1.

 

Recognition of status transferred via external sensors to the discrete inputs and transfer via the engine 

CAN bus to the higher level control unit that is coupled with the IKD 1. Evaluation is proceeded according 

to the configured action and additional steps are initiated. 

2.

 

Output of signals to the relays that are received from the higher level control unit. For this feature it is 

possible to configure the relays of the IKD 1 using the relay manager of the higer level control unit (please 

note external description of higher level control unit). 

 

Coupling to a PLC 

1.

 

Recognition of status transferred via external sensors to the discrete inputs and transfer via the engine 

CAN bus to the PLC that is coupled with the IKD 1. Evaluation is proceeded according to the program in 

the PLC. 

2.

 

Output of signals to the relays that are received from the PLC. For this feature the relays have to be con-

trolled from the PLC 

 

 

Содержание IKD 1










































Отзывы:

Нет отзывов