Woodward IKD 1 Скачать руководство пользователя страница 18 | Manualshive

Страница: 18 / 41

Woodward IKD 1 Скачать руководство пользователя страница 18

Manual 37135C

IKD 1 - Digital I/O Expansion Board

Page 18/41

© Woodward

Discrete Inputs

≡≡≡≡≡≡≡≡≡≡≡≡≡≡≡≡≡≡≡≡≡≡≡≡≡

For each discrete input the following parameters can be configured separately:

•

type of action (NO/NC),

•

alarm class (control input, class 0, 1, 2 or 3),

•

tripping delay,

•

release delay,

•

enable conditions,

•

type of resetting, and

•

is the input used as a remote acknowledgment input.

Relay Outputs

≡≡≡≡≡≡≡≡≡≡≡≡≡≡≡≡≡≡≡≡≡≡≡≡≡

For each relay output the following parameters can be configured separately:

•

type of action (NO/NC),

•

base status (during CAN bus failure),

•

is the relay 1 used as a readiness for operation relay (using this setting no other function can be assigned to

the relay) and

•

is a CAN bus failure is recorded via a relay. (Note: If you want to record time-critical alarms via a relay

please use the relays directly contained in the higher level control unit to eliminate delays caused by CAN

run-times.)

Configuration Options

≡≡≡≡≡≡≡≡≡≡≡≡≡≡≡≡≡≡≡≡≡≡≡≡≡

The following options exist for configuration. Configuration can be done alternatively via

•

the configuration plug using the direct configuration cable DPC and the PC program LeoPC1

•

the CAN bus using the D-1 unit

«
...
16
17
18
19
20
...
»

Содержание IKD 1










































Отзывы:

Нет отзывов