Woodward IKD 1 Скачать руководство пользователя страница 28 | Manualshive

Страница: 28 / 41

Woodward IKD 1 Скачать руководство пользователя страница 28

Manual 37135C

IKD 1 - Digital I/O Expansion Board

Page 28/41

© Woodward

CAN alarm relay -

logical OR

CAN fault relay and set status combined with OR

YES/NO

YES

.............. As long as no CAN fault is present the relay configured as a CAN fault

relay can be used as a normal relay. If a CAN fault is present this relay

is enabled following the delay time. It can be reset if the CAN fault is

not present anymore.

NO

................ This relay is set only if a CAN fault is present. It can be reset if the

CAN fault is not present anymore.

Note:

Above configured type is taken into account!

Relay x basic set.

active

Base status during CAN fault

YES/NO

A base status can be configured for every relay that is chosen while a CAN fault is

present. This setting is taken into account only if this is additionally enabled below.

The relay remains in this status until the CAN fault has been acknowledged (ac-

knowledgment can alternatively be carried out via the self acknowledgment, via the

CAN bus (if this is working again) or via the configured discrete input).

YES

.............. The relay reacts according to the set status.

NO

................ The relay reacts according to the reset status.

Note:

Above configured type is taken into account!

Basic setting

Relay reaction at CAN faults

YES/NO

During a CAN fault the relays can be set into the above configured base setting.

YES

.............. All relays (except the configured CAN fault relay) are changed into

base status following the CAN fault delay time.

NO

................ All relays (except the configured CAN fault relays) remain in the status

prior to the CAN fault.

Note:

Above configured type is taken into account!

«
...
26
27
28
29
30
...
»

Содержание IKD 1










































Отзывы:

Нет отзывов