manualshive.com logo in svg

Woodley InSight V-CHEM, Руководство по обслуживанию

Поделиться
Скачать
Woodley InSight V-CHEM Скачать руководство пользователя страница 81

  

  

75 

 

 

 

9.3.1

 

Reasons 

1)

 

The router settings contain an unrecognised name and password. 

2)

 

Software programs have bugs and need to be upgraded. 

 

9.3.2

 

Troubleshooting 

1)

 

Scan the surrounding signal strength. 

2)

 

Open the Wi-Fi on a mobile phone and set the password. Use the device to scan for a 

hotspot and connect. 

3)

 

If you have completed all the above steps and still can't connect to Wi-Fi, contact 

Woodley Equipment Company. 

 

9.4

 

Reference Ranges are  Inaccurate 

After the upgrade procedure, the reference range units, both SI standard units and Common 

standard units, seem inaccurate. 

 

9.4.1

 

Reasons 

The operator manually modified the reference ranges during use but did not delete this file 

when  upgrading  the  software.  Therefore,  it  co-existed  with  the  newly  upgraded  file, 

resulting in confusion on the display. 

 

9.4.2

 

Troubleshooting 

Contact Woodley Equipment Company to get a specific version of the software to upgrade, 

cover the corresponding files and then upgrade to the latest version. 

Содержание InSight V-CHEM

























































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды